Hi Leute,
ich habe seit einigen Tagen das Problem, dass meine DM7020 aus dem Deep Standby nicht mehr richtig startet. Sie bootet komplett hoch, allerdings erscheint nach dem Bootscreen kein Fernsehbild. Enigma arbeitet normal (man kann das OSD und die Menus sehen etc.). Wenn ich die die Box dann herunterfahre und neu starte funktioniert alles normal.
Das Problem wurde auch nicht durch erneutes einspielen des Gemini-Images behoben (z.Zt Version 3.40).
Warum ich auf ein Flash Problem komme? Mich machen einige Kernel-Mitteilungen stutzig (siehe rote Markierungen):
<6>ibm-iic1: using standard (100 kHz) mode
<6>NET: Registered protocol family 2
<6>IP: routing cache hash table of 512 buckets, 4Kbytes
<6>TCP: Hash tables configured (established 4096 bind 8192)
<6>NET: Registered protocol family 1
<6>NET: Registered protocol family 17
<5>jffs2_scan_dirent_node(): Name CRC failed on node at 0x012751d4: Read 0x4df47
ff5, calculated 0x24f2bd0b
<5>jffs2_scan_dirent_node(): Node CRC failed on node at 0x012a7bf0: Read 0xfffff
fff, calculated 0x8e26e788
<4>Empty flash at 0x012a7c20 ends at 0x012a7e00
<4>Empty flash at 0x0149fc90 ends at 0x0149fe00
<4>Empty flash at 0x014ef858 ends at 0x014efa00
<4>Empty flash at 0x015e7404 ends at 0x015e7600
<4>Empty flash at 0x01a3b450 ends at 0x01a3b600<4>VFS: Mounted root (jffs2 filesystem).
<6>Mounted devfs on /dev
<4>Freeing unused kernel memory: 88k init
<4>Warning: unable to open an initial console.
<5>jffs2_get_inode_nodes(): CRC failed on node at 0x015e73c0: Read 0xffffffff, c
alculated 0x45e9a0dc<5>jffs2_get_inode_nodes(): Data CRC failed on node at 0x01a3b34c: Read 0xd74563
16, calculated 0xb069114c
<5>jffs2_get_inode_nodes(): Data CRC failed on node at 0x0149fa84: Read 0x62e873
0c, calculated 0xbc193d45
<6>kjournald starting. Commit interval 5 seconds
<6>EXT3 FS on hda1, internal journal
<6>EXT3-fs: mounted filesystem with ordered data mode.
<4>head: module license 'Proprietary' taints kernel.
<4>using HW buffers at 64 MB, 0x84000000
<4>read CA...
<4>CA dump:
<4>01 01 09
<4>02 01 02
<4>03 04 00 00 35 4b
<4>04 06 00 09 34 14 0b 4a
<4>05 02 01 01
<4>06 08 32 30 30 35 30 34 31 32
<4>07 0f 35 34 31 32 30 39 31 32 30 30 31 33 36 34 33
<4>08 01 00
<4>ff 01 9d
<4>lnbp21: attaching lnbp21 at 0x08 to adapter IBM IIC
<4>using 84900000 as framebuffer base
<4>VID_DISP_MODE set to 0088e6c0
<4>registered framebuffer
<4>allocated major 250 for denc.
<4>[DENC] set PAL
<4>[DENC] disable WSS
<4>[DENC] disable WSS
<4>[DENC] disable WSS
<4>SET IR GPIOS
<4>demux set source
<5>core: Loaded IBM STB04xxx core driver
<4>write 1 event's ...
<4>[DENC] disable WSS
<4>audio init
<4>AUDIO_CLEAR_BUFFER
<4>demux: init
<4>xp0_clk_stop
<4>registering frontend...
<4>disable continuous tone
<7>stv: already got one.
<4>stb04_pig: $Id: stb04_pig.c,v 1.14 2006/05/31 18:23:01 ghost Exp $
<4>lcd.o: LCD driver (KS0713) module
<4>avs: attaching avs at 0x94 to adapter IBM IIC
<4>[AVS] set 0V
<4>rfmod: INITed
<4>[CI] insert detected
<4>VIDEO_SELECT_SOURCE
<4>open video clip-mode
<4>VIDEO_CLEAR_BUFFER
<4>VIDEO_PLAY / VIDEO_CONTINUE, state 1 0
<4>VIDEO_STOP, state 0
<4>VIDEO_SELECT_SOURCE
<4>VIDEO_CLEAR_BUFFER
<4>VIDEO_PLAY / VIDEO_CONTINUE, state 1 0
<4>VIDEO_STOP, state 0
<4>hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
<4>hda: task_no_data_intr: error=0x04 { DriveStatusError }
<4>ide: failed opcode was: 0xef
<4>setting 414720 bytes to 0
<4>set event: 00000049
<4>set net_dream_mode to 1
<4>disable ci
<4>demux set source
<4>[CI] RESET
<4>[CI] init try #0
<5>jffs2_get_inode_nodes(): Data CRC failed on node at 0x014eeeb4: Read 0x6fb88c
6a, calculated 0x89d7f063
<4>[CI] Init complete after 1 tries
<4>[CI] POLLIN ci_state_change
etc, etc, etc...
Hatte von euch jemand schon mal dieses Problem? Kann mir jemand helfen/ sagen was ich tun kann?
In der Boardsuche bin ich leider auf nichts gestoßen, was mir weiter geholfen hätte.
Vielen Dank im Voraus...