hallo leute,
ich habe eben erfolgreich ein upgrade der firmware meines philips 32pf9830 gemacht. ich hatte die JX21E-1.2.0.0 00741 und bin nun auf die JX21E-1.8.0.0 01131 gewechselt. ich hoffe mal es ist die neueste, habe auch keine andere gefunden gehabt.
währe schon noch ein paar infos von euch zu bekommen, da ja schon einige diese gerät hier im ihad ihr eigen nennen.
ZitatAlles anzeigenAutomatisches Software-Upgrade-Verfahren
& Schalten Sie Ihr Fernsehgerät aus und entfernen Sie alle Speichergeräte.
é Führen Sie den USB-Speicherstick, der die heruntergeladene aktualisierte
Software enthält, ein.
“ Schalten Sie Ihr Fernsehgerät mit der Netztaste B oben auf Ihrem
Fernsehgerät ein.
‘ Beim Anlauf wird das Fernsehgerät den USB-Speicher scannen, bis
Update gefunden wird. Das Fernsehgerät wird automatisch auf den
Upgrade-Modus umschalten. Nach einigen Sekunden wird es den Stand
Upgrade-Verfahrens anzeigen.
Achtung:
• Entfernen Sie den USB-Speicherstick nicht während des Software-Upgrade-
Verfahrens!
• Im Falle eines Stromausfalles während des Upgrade-Verfahrens sollen
USB-Speicherstick nicht aus dem Fernsehgerät herausnehmen. Das Fernsehgerät
wird die Aktualisierung fortsetzen, wenn der Strom wieder vorhanden ist.
• Wenn Sie versuchen, auf dieselbe oder eine frühere Version der Software
aktualisieren, wird um eine Bestätigung gebeten. Einen Software-Downgrade
sollten Sie nur in Notfällen durchführen.
• Wenn während des Upgrade-Verfahrens ein Fehler eintritt, müssen Sie
Verfahren wiederholen oder Kontakte mit Ihrem Händler aufnehmen.
( Wenn die Software-Aktualisierung erfolgreich war, entfernen Sie den USBSpeicherstick
und schalten Sie Ihr Fernsehgerät mit der Netztaste
auf Ihrem Fernsehgerät wieder ein.
Ihr Fernsehgerät wird mit der neuen Software starten.
Achtung:Wenn die Aktualisierung beendet ist, können Sie über Ihren PC
Software des Fernsehgeräts von Ihrem USB-Speicherstick löschen.
ZitatAlles anzeigen
PHILIPS FLAT TV SOFTWARE UPGRADE
WITH USB PORTABLE MEMORY
Introduction
------------
Philips offers software upgrade capability for your TV using portable memory.
After you have completed a software upgrade, your TV will typically perform
better. What improvements are made depends on the upgrade software you are
using as well as the software your TV contained before the upgrade.
You can execute the software upgrade procedure yourself.
Be aware that the content of this document is addressing technical or software
skilled users.
Preparing a portable memory for software upgrade
------------------------------------------------
For the procedure you will require:
- A personal computer with web browsing capability.
- An archive utility that supports the ZIP-format (e.g. WinZip for Windows
or StuffIt for Mac OS).
- A preferably empty USB memory stick.
Note: Only FAT/DOS-formatted portable memory is supported.
New software can be obtained from your dealer or can be downloaded from the
http://www.philips.com/support website:
[1] Go to http://www.philips.com/support using the web browser on your PC
[2] Follow the procedure to find the information and the software related
to your TV.
[3] Select the latest software upgrade file and download it to your PC.
[4] Decompress the ZIP-file and copy the file "autorun.upg" to the root
directory of the USB portable memory.
Note: Only use software upgrades that can be found on the
http://www.philips.com/support web site.
Verifying the version of the TV software
----------------------------------------
Before starting the software upgrade procedure, it is advised to check what
the current TV software is.
[1] Select Software Upgrade in the Installation menu.
[2] Press the cursor right.
The Software Upgrade menu moves to the left panel.
[3] Select Current Software Info to observe the version and the description
of the current software.
Automatic software upgrade procedure
------------------------------------
[1] Power off your TV and remove all memory devices.
[2] Insert the USB portable memory that contains the downloaded software
upgrade.
[3] Switch on your TV with the power switch at the right side of the TV.
[4] At startup the TV will scan the USB portable memory until it finds the
update content. The TV will automatically go to the upgrade mode. After a
few seconds it will display the status of the upgrade procedure.
Warning:
- You are not allowed to remove the USB portable memory during the
software upgrade procedure!
- In case of a power drop during the upgrade procedure, don’t remove the
USB portable memory from the TV. The TV will continue the upgrade as
soon as the power comes back.
- If you try to upgrade to a software version lower than the current
version, a confirmation will be asked.
Downgrading to older software should only be donw in case of real
necessity.
- If an error occurs during the upgrade you should retry the procedure
or contact your dealer.
[5] When the software upgrade was successful, remove the USB portable memory
and restart your TV with the power switch at the right side of the TV.
Your TV will start up with the new software.
Note: Once the upgrade is finished use your PC to remove the TV software
from your USB portable memory.
Manual software upgrade procedure
---------------------------------
For a manual software upgrade copy the "autorun.upg" file in a directory
called "Upgrades" located in the root of the USB portable memory.
[1] Insert the portable memory that contains the downloaded software upgrade.
[2] Select Software Upgrade in the Installation menu.
Go to Local upgrades/applications.
The TV will list all compatible images available on the USB portable
memory and display the data for each selected upgrade image.
[3] Select the correct upgrade image and press the red color button to start
the upgrade.
Your TV will restart and will automatically go to the upgrade mode. After
a few seconds it will display the status of the upgrade procedure.
Warning:
- If you try to upgrade to a software version equal or lower than the
current version, a confirmation will be asked. Downgrading to older
software should only be done in case of real necessity.
[4] When the software upgrade was successful, remove the USB portable memory
and restart your TV with the power switch at the right side of the TV.
Your TV will start up with the new software.
Software History
----------------
JX21E-1.8.0.0 01131
Following problems are solved :
• Occasional green flashes in 4:3 mode
Following changes have been implemented:
• Improved support for certain set-top boxes
JX21E-1.4.1.0 00991
Only to be used on 32PF9830/10, 37PF9830/10 and 42PF9830/10.
Following problems are solved :
• Analog Canal+ decoder not working in France
JX21E-1.4.0.0 00761
First release containing Connected Planet functionality (for sets supporting
it) and digital video playback. Only to be used on 42PF9830/10.
JX21E-1.3.0.0 00751
Internal release only, should not be used in the field.
JX21E-1.2.0.0 00741
Only to be used on 32PF9830/10 and 37PF9830/10.
Following problems are solved :
• Updated Software Upgrade application to resolve device detection problem
JX21E-1.1.0.0 00731
Only to be used on 32PF9830/10 and 37PF9830/10.
Following problems are solved :
• Updated picture profiles to soften the image
JX21E-1.0.0.0 00721
Initial commercial release. Only to be used on 32PF9830/10 and 37PF9830/10.
PS: weiss nicht ob ich die sw hier hochladen kann, sind ca. 18,5mb????