QTS 4.3.4.xxxx

  • mal sehen was diesmal in der Version wieder schief läuft :-)


    QTS 4.3.4.0593 build 20180524


    [Important Notes]
    - This QTS update changes the file system of the system partition to ext4 for ARM-based models with Annapurna Labs processors. For data security reasons, you are not able to downgrade QTS to a previous version after this update.
    Affected models: TS-131P, TS-231P, TS-431P, TS-531P, TS-231+, TS-431+, TS-231P2, TS-431P2, TS-431X, TS-431X2, TS-531X, TS-831X, TS-1231XU-RP, TS-1231XU, TS-831XU-RP, TS-831XU, TS-431XU-RP, TS-431XU, TS-431XeU, and TS-1635.
    - To ensure system stability, QNAP recommends updating and then restarting QVPN Service in App Center after you update QTS to 4.3.4.
    - As QTS previous versions of ARM models do not support snapshots, when you upgrade to QTS 4.3.4, the original volume cannot use this feature immediately. To solve this problem, you have to back up the existing data on your QNAP NAS to external storage. Then you can rebuild the QNAP NAS and take snapshots to the new storage pool with multiple volumes.
    - QTS 4.3.4 is the final available firmware update for the following models:
    TS-EC1679U-SAS-RP, TS-EC1679U-RP, TS-1679U-RP, TS-EC1279U-SAS-RP, TS-EC1279U-RP, TS-1279U-RP, TS-1079 Pro, TS-EC879U-RP, TS-879U-RP, TS-1270U-RP, TS-870U-RP, TS-470U-RP, TS-470U-SP, TS-1269U-RP, TS-869U-RP, TS-469U-RP, TS-469U-SP, TS-879 Pro, TVS-870, TS-870 Pro, TS-870, TVS-670, TS-670 Pro, TS-670, TVS-470, TS-470 Pro, TS-470, TS-869 Pro, TS-869L, TS-669 Pro, TS-669L, TS-569 Pro, TS-569L, TS-469 Pro, TS-469L, TS-269 Pro, TS-269L, IS-400 Pro.
    - For the status of QTS updates and maintenance for your NAS model, visit https://www.qnap.com/en/product/eol.php
    - When QTS 4.3.x is installed on NAS models running on 64-bit Intel and AMD processors, some applications may not be supported. To check if installed apps on your NAS are compatible with QTS 4.3.x, download the QTS 64-bit compatibility tool and install it on your current QTS build. (https://download.qnap.com/QPKG/CF64_0.1-1114.qpkg.zip)
    - Starting from QTS 4.3.4, QNAP NAS devices no longer support creating storage pools or static volumes using NVMe PCIe/M.2 SSDs. However, this limitation does not apply to the SSDs installed in built-in M.2 slots or on QM2 expansion cards.
    - Below are the kernel versions for the NAS models supported by QTS 4.3.4.0479:
    kernel 3.10.20: TS-128, TS-228
    kernel 3.2.26: TS-x31, TS-x31U
    kernel 3.4.6: TS-x69, TS-x69U, TS-x69L
    kernel 4.2.8: HS-251, IS-400, SS-x79U, TS-x79, TS-x79U, SS-x79U, TS-x70, TS-x70U, TVS-x70, TS-x31P, TS-x31P2, TS-x31+, TS-x31X, TS-x31XU, TS-x28A, TS- x35, TS-x51, TS-x51A, TS-x51U, TS-x53, TS-x53A, TBS-x53A, TS-x53B, TS-x53BU, TS-x53S, IS-453S, TS-x53U, TVS-x63, TS-x63, TS-x63U, TS-x73U, TS-x77, TVS-x80, TS-x80, TVS-x80U, TS-x80U, TVS-x82, TVS-x82S, TVS-1582TU, TS-x85, TES-x85U, TDS-16489U, TVS-x71, TVS-x71U, TVS-x73


    [Fixed Issues]
    - Users could not close the privacy policy announcement when accessing QTS using Firefox.
    - Users could not connect to the NAS after syncing the files in two shared folders with two client devices via Qsync.
    - Files and subfolders in encrypted shared folders would sometimes disappear after a data migration.
    - Users could not back up iSCSI LUNs to the shared folders on devices running Windows 10 Pro.
    - Users could not access the NAS from Windows if the Samba configuration file was corrupted.
    - QTS System Logs could not display connection logs for FTP connections.
    - Users could not specify passwords that contained a large number of special characters.
    - QTS would automatically create a virtual switch after users restarted the NAS.
    - Control Panel could only list up to 1000 domain computers.
    - Users could not back up NAS shared folders using scheduled backup on Windows Server 2012 R2.
    - Certain folders deleted via SMB would be recovered automatically.
    - QTS would automatically translate certain folder names after users changed the system language.

  • Bin ja mutig und hab' das Update eingespielt.


    QNAP ist hochgekommen und es scheint alles zu laufen.
    Bin gespannt, ob der HDD-Sleepmodus endlich wieder funktioniert...

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)

  • Das Thema Sleep hatte ich auch gehabt.
    Bis mir ein netter Supporter zuerst ein Update für den Controller geschickt hatte
    und danach eines für das BIOS.
    Seither gehen sie auch wieder pennen.


    Ich glaub ich brauch auch mal so ein Update für mich ;)


    Kannst ja mal sagen ob noch in ein paar Tagen alles rennt auf deinen Qnap

  • So langsam wird es echt peinlich.


    Die 0593 wurde zurückgezogen.


    Dafür gibt es jetzt eine neue 0597.... mal sehen, ob die hält

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)

  • Für Qnap gibt es dafür glatt :rot:


    So lange die aber, wie du ja schon geschrieben hast,
    kaum noch Beta Tests fahren wird sich wohl kaum was an der Verfahrensweise ändern.
    Die neuen Beta Tester sind die User auf deren Buckel das ausgetragen wird.


    Ich jedenfalls bin es nicht und stinke sauer inzwischen auf den Laden.


    So lange die denken wir User haben nichts besseres zu tun als permanent Backups zu fahren
    um dann wieder heraus zu finden das die nächste Version auch wieder Müll ist
    werde ich bei meiner 516 bleiben.


    Mein Mitleid haben die Admins von Produktivsystemen auf jeden Fall.

  • Da kann man ja froh sein, wenn das eigene Modell "out of support" ist und keine neuen Firmwares mehr kriegt bzw. höchstens noch Sicherheitsupdates :tongue:

  • Die Installation der 0597 hat bei meiner TS-569L problemlos geklappt und es scheint auch alles noch zu laufen.


    HDD Standby klappt aber leider damit weiterhin nicht :(

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)

  • Hab' jetzt auch erstmal die Nase voll und bin zurück auf die 0516. Damit funktioniert alles, was ich so brauche inkl. HDD Standby.

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)

  • QTS 4.3.4.0597 build 20180528


    [Fixed Issues]
    - Users could not close the privacy policy announcement when accessing QTS under certain circumstances.
    - Users could not connect to the NAS after syncing the files in two shared folders with two client devices via Qsync.
    - Files and subfolders in encrypted shared folders would sometimes disappear after a data migration.
    - Users could not back up iSCSI LUNs to the shared folders on devices running Windows 10 Pro.
    - Users could not access the NAS from Windows if the Samba configuration file was corrupted.
    - QTS System Logs could not display connection logs for FTP connections.
    - Users could not specify passwords that contained a large number of special characters.
    - QTS would automatically create a virtual switch after users restarted the NAS.
    - Control Panel could only list up to 1000 domain computers.
    - Users could not back up NAS shared folders using scheduled backup on Windows Server 2012 R2.
    - Certain folders deleted via SMB would be recovered automatically.
    - QTS would automatically translate certain folder names after users changed the system language.

  • :aufsmaul:


    Version 4.3.4.0597


    Fingerchen weg, wenn kein Backup existiert und die/das Volumen verschlüsselt ist

  • Neue FW mit ganz vielen Fixes:


    QTS 4.3.4.0644 build 20180710


    [Important Notes]
    - This QTS update changes the file system of the system partition to ext4 for ARM-based models with Annapurna Labs processors. For data security reasons, you are not able to downgrade QTS to a previous version after this update.
    Affected models: TS-131P, TS-231P, TS-431P, TS-531P, TS-231+, TS-431+, TS-231P2, TS-431P2, TS-431X, TS-431X2, TS-531X, TS-831X, TS-1231XU-RP, TS-1231XU, TS-831XU-RP, TS-831XU, TS-431XU-RP, TS-431XU, TS-431XeU, and TS-1635.
    - To ensure system stability, QNAP recommends updating and then restarting QVPN Service in App Center after you update QTS to 4.3.4.
    - As QTS previous versions of ARM models do not support snapshots, when you upgrade to QTS 4.3.4, the original volume cannot use this feature immediately. To solve this problem, you have to back up the existing data on your QNAP NAS to external storage. Then you can rebuild the QNAP NAS and take snapshots to the new storage pool with multiple volumes.
    - QTS 4.3.4 is the final available firmware update for the following models:
    TS-EC1679U-SAS-RP, TS-EC1679U-RP, TS-1679U-RP, TS-EC1279U-SAS-RP, TS-EC1279U-RP, TS-1279U-RP, TS-1079 Pro, TS-EC879U-RP, TS-879U-RP, TS-1270U-RP, TS-870U-RP, TS-470U-RP, TS-470U-SP, TS-1269U-RP, TS-869U-RP, TS-469U-RP, TS-469U-SP, TS-879 Pro, TVS-870, TS-870 Pro, TS-870, TVS-670, TS-670 Pro, TS-670, TVS-470, TS-470 Pro, TS-470, TS-869 Pro, TS-869L, TS-669 Pro, TS-669L, TS-569 Pro, TS-569L, TS-469 Pro, TS-469L, TS-269 Pro, TS-269L, IS-400 Pro.
    - For the status of QTS updates and maintenance for your NAS model, visit https://www.qnap.com/en/product/eol.php
    - When QTS 4.3.x is installed on NAS models running on 64-bit Intel and AMD processors, some applications may not be supported. To check if installed apps on your NAS are compatible with QTS 4.3.x, download the QTS 64-bit compatibility tool and install it on your current QTS build. (https://download.qnap.com/QPKG/CF64_0.1-1114.qpkg.zip)
    - Starting from QTS 4.3.4, QNAP NAS devices no longer support creating storage pools or static volumes using NVMe PCIe/M.2 SSDs. However, this limitation does not apply to the SSDs installed in built-in M.2 slots or on QM2 expansion cards.
    - Below are the kernel versions for the NAS models supported by "QTS 4.3.4.0644":
    kernel 3.10.20: TS-128, TS-228
    kernel 3.2.26: TS-x31, TS-x31U
    kernel 3.4.6: TS-x69, TS-x69U, TS-x69L
    kernel 4.2.8: HS-251, IS-400, SS-x79U, TS-x79, TS-x79U, TS-x70, TS-x70U, TVS-x70, TS-x31P, TS-x31P2, TS-x31+, TS-x31X, TS-x31XU, TS-x28A, TS- x35, TS-x51, TS-x51A, TS-x51U, TS-x53, TS-x53A, TBS-x53A, TS-x53B, TS-x53BU, TS-x53S, IS-453S, TS-x53U, TVS-x63, TS-x63, TS-x63U, TS-x73U, TS-x77, TVS-x80, TS-x80, TVS-x80U, TS-x80U, TVS-x82, TVS-x82S, TVS-1582TU, TS-x85, TES-x85U, TDS-16489U, TVS-x71, TVS-x71U, TVS-x73


    [Fixed Issues]
    - Fixed a vulnerability in PHP (CVE-2018-7584).
    - Fixed a command injection vulnerability in Helpdesk (CVE-2018-0714).
    - Fixed multiple vulnerabilities in FFmpeg.
    - Fixed a vulnerability in DDNS.
    - Users could not fully move files between volumes. Deleting the task would cause the files to disappear from both source and destination volumes.
    - Creating an encrypted shared folder in a subfolder would cause files in the same folder to disappear.
    - The TS-x31 series would sometimes randomly restart after handling I/O intensive operations for a long time.
    - Snapshot Replica and Snapshot Vault would display transfer sizes that were inconsistent with actual data sizes.
    - Snapshot Replica Job Wizard would stop responding when performing a test if the destination NAS did not have sufficient available space.
    - Storage and Snapshots would stop responding when users performed an IOPS read test after a sequential read test.
    - Users could not revert iSCSI LUN snapshots that were replicated from Snapshot Vault.
    - United Kingdom was missing from the country list in the billing information on the QNAP License Store website.
    - Unlocking an encrypted volume would cause Domain Controller to be disabled and all domain settings to revert to the default.
    - Using the ext4 file system on certain versions of QTS would cause SMB shared folder names to become case sensitive.
    - QTS would still move deleted files to the @Recycle folder even when Network Recycle Bin was disabled.
    - The CPU usage of a certain process would increase abnormally after users enabled Domain Controller.
    - Users could not view or access the snapshot shared folders created in File Station.
    - Users could not apply a Let's Encrypt certificate after enabling DDNS Service and Virtual Host.
    - Users could not connect to the NAS via myQNAPcloud again after changing the WAN IP address.
    - Users could not set 1.1.1.x as the static IP address of a network interface.
    - After users created an ISO shared folder from an external drive, File Station would mistake the external drive for an optical disc, thus denying users write permissions.
    - When performed in an isolated network environment, snapshot replica jobs would stop responding and then time out.
    - The LCD panel of the UX-800P would stay on and remain blank for a long time.
    - Storage and Snapshots would mistake the drives installed on the UX-800U-RP for external drives.
    - Users could not revert the snapshots of a snapshot shared folder when HybridDesk Station was started.
    - It would take longer to start the TS-431P2 under certain circumstances.
    - The NAS could not enter the Disk Standby Mode after users enabled Advanced Folder Permissions.
    - Disk Secure Erase tasks would stop responding and could not be canceled after users restarted the NAS.
    - Users could not create an SSD cache of 1 TB on the TS-431P2.
    - After deleting an encrypted shared folder, users could not create another encrypted shared folder with the same name and password.
    - Enabling Disk Standby Mode would hinder the NAS from reporting disk information via the SNMP service.
    - File transfer using SMB via L2TP might cause errors and file corruption.
    - Database errors would occur when users logged on to Qsync Client using the format "username@domain".
    - Storage and Snapshots sometimes could not display certain snapshots after users had taken a large number of snapshots.
    - Music Station could not correctly display certain Japanese file names.
    - QTS would switch to software-based transcoding after performing hardware-accelerated transcoding for over 20 minutes.
    - File Station would display the "Transfer to Dedicated Volume" option even on the NAS models that did not support creating snapshot shared folders.
    - Users could not include certain special characters in the password of an encrypted folder.
    - After connecting two printers of the same model to the NAS via Samba, only one of them would be detected.
    - Several seconds after users opened File Station, certain buttons on the toolbar would disappear.
    - The LCD panel of the UX-800P would stay on and display incorrect messages after users updated QTS on the NAS connected to the UX-800P.
    - Snapshot replica creation wizard would display certain strings in Korean when Japanese was selected as the display language.
    - QTS could not correctly display the Qboost icon when the screen resolution and browser zoom level were both high.
    - File Station and Music Station could not generate thumbnails for certain music files.
    - File Station could not sort files correctly when file names included special characters or spaces.
    - Users could not migrate a shared folder that contained a large number of files to a snapshot shared folder.
    - Users could only run a snapshot replica job once.

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)

  • Nachtrag zur 0644


    - Installation lief bei meiner NAS problemlos
    - Bisher keinerlei Probs festgestellt
    - HDD-Standby funktioniert endlich wieder :)

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)

  • Na dann auf zum fröhlichen Backup hier :-)


    Das Thema HDD schlafen hatte ich auch, bis mir ein netter Supporter, ist schon Monaten
    her, ein BIOS Update geschickt hatte. Seitdem ist Ruhe.

  • QNAP hat schon seit je her immer wieder Probs mit dem HDD-Sleep.
    Betroffen sind nicht immer alle, daher wohl auch immer wieder schwer greifbar.


    Bei meinen TS-569x war nach 0516 Schluss mit HDD-Sleep. Das hatte ich aber bei früheren FWs und Betas auch immer wieder mal.


    In der 0644 wurde auch ausdrücklich etwas diesbezüglich gefixt:
    "- The NAS could not enter the Disk Standby Mode after users enabled Advanced Folder Permissions."

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)

  • QTS 4.3.4.0675 build 20180810


    [Important Notes]
    - This QTS update changes the file system of the system partition to ext4 for ARM-based models with Annapurna Labs processors. For data security reasons, you are not able to downgrade QTS to a previous version after this update.
    Affected models: TS-131P, TS-231P, TS-431P, TS-531P, TS-231+, TS-431+, TS-231P2, TS-431P2, TS-431X, TS-431X2, TS-531X, TS-831X, TS-1231XU-RP, TS-1231XU, TS-831XU-RP, TS-831XU, TS-431XU-RP, TS-431XU, TS-431XeU, and TS-1635.
    - To ensure system stability, QNAP recommends updating and then restarting QVPN Service in App Center after you update QTS to 4.3.4.
    - As QTS previous versions of ARM models do not support snapshots, when you upgrade to QTS 4.3.4, the original volume cannot use this feature immediately. To solve this problem, you have to back up the existing data on your QNAP NAS to external storage. Then you can rebuild the QNAP NAS and take snapshots to the new storage pool with multiple volumes.
    - QTS 4.3.4 is the final available firmware update for the following models:
    TS-EC1679U-SAS-RP, TS-EC1679U-RP, TS-1679U-RP, TS-EC1279U-SAS-RP, TS-EC1279U-RP, TS-1279U-RP, TS-1079 Pro, TS-EC879U-RP, TS-879U-RP, TS-1270U-RP, TS-870U-RP, TS-470U-RP, TS-470U-SP, TS-1269U-RP, TS-869U-RP, TS-469U-RP, TS-469U-SP, TS-879 Pro, TVS-870, TS-870 Pro, TS-870, TVS-670, TS-670 Pro, TS-670, TVS-470, TS-470 Pro, TS-470, TS-869 Pro, TS-869L, TS-669 Pro, TS-669L, TS-569 Pro, TS-569L, TS-469 Pro, TS-469L, TS-269 Pro, TS-269L, IS-400 Pro.
    - For the status of QTS updates and maintenance for your NAS model, visit https://www.qnap.com/en/product/eol.php
    - When QTS 4.3.x is installed on NAS models running on 64-bit Intel and AMD processors, some applications may not be supported. To check if installed apps on your NAS are compatible with QTS 4.3.x, download the QTS 64-bit compatibility tool and install it on your current QTS build. (https://download.qnap.com/QPKG/CF64_0.1-1114.qpkg.zip)
    - Starting from QTS 4.3.4, QNAP NAS devices no longer support creating storage pools or static volumes using NVMe PCIe/M.2 SSDs. However, this limitation does not apply to the SSDs installed in built-in M.2 slots or on QM2 expansion cards.
    - Below are the kernel versions for the NAS models supported by "QTS 4.3.4.0675":
    kernel 3.10.20: TS-128, TS-228
    kernel 3.2.26: TS-x31, TS-x31U
    kernel 3.4.6: TS-x69, TS-x69U, TS-x69L
    kernel 4.2.8: HS-251, IS-400, SS-x79U, TS-x79, TS-x79U, TS-x70, TS-x70U, TVS-x70, TS-x31P, TS-x31P2, TS-x31+, TS-x31X, TS-x31XU, TS-x28A, TS- x35, TS-x51, TS-x51A, TS-x51U, TS-x53, TS-x53A, TBS-x53A, TS-x53B, TS-x53BU, TS-x53S, IS-453S, TS-x53U, TVS-x63, TS-x63, TS-x63U, TS-x73U, TS-x77, TVS-x80, TS-x80, TVS-x80U, TS-x80U, TVS-x82, TVS-x82S, TVS-1582TU, TS-x85, TES-x85U, TDS-16489U, TVS-x71, TVS-x71U, TVS-x73


    [Fixed Issues]
    - Fixed a stack-based buffer overflow vulnerability (CVE-2018-0721).
    - Fixed a cross-site scripting vulnerability (CVE-2018-0719).
    - Write speeds on external NTFS disks during file transfer were slower than expected.
    - Users could not access exFAT disks after updating QTS to 4.3.4.0644 20180710 on the TS-x69 models.
    - Creating an encrypted shared folder in a subfolder would cause files in the same folder to disappear.
    - Devices on the same network as the NAS sometimes could not obtain IP addresses via DHCP when UPnP Discovery Service and secure connection (HTTPS) were both enabled.
    - Users could not enable CodexPack when certain Nvidia graphics cards were installed.
    - After users installed an SSL certificate via myQNAPcloud, if users recovered the QTS default certificate, myQNAPcloud would automatically install the SSL certificate again.
    - The "Replace Disk One by One" option in Storage & Snapshots would become unavailable after users set a disk as the spare disk.
    - It would sometimes take longer to start the NAS after a storage pool or volume was created.
    - Control Panel could not display domain computers due to unexpected connection timeouts.
    - Users could not change the configuration of a storage pool from RAID 1 to RAID 5 when using M.2 SSDs.
    - App Center did not notify users of available updates for License Center.
    - On the TS-x28A models, users could still connect to the NAS from blocked IP addresses.
    - Users could not scroll the list of available domain controllers on the Active Directory Wizard in "Control Panel" > "Privilege" > "Domain Security".
    - Garbled texts would appear when users opened certain .txt files in File Station.
    - On Safari, File Station would stop responding when users uploaded files by dragging and dropping files.
    - Users could not find torrents from certain sources when performing a search in Download Station.
    - The dates modified of files might be inconsistent with the client time when users accessed shared folders via SMB.
    - Mac Finder would display a QNAP NAS with a question mark icon when users accessed shared folders via SMB.
    - Color tags attached to files would disappear after Mac woke up from sleep if users accessed shared folders via SMB.
    - Snapshot log entries would not be sorted from the latest to the oldest when DD-MM-YY was used as the date format.
    - QTS would incorrectly report false SNMP DoS (denial-of-service) attacks.
    - Users could not securely erase SSDs when 2-step verification was enabled.
    - QTS could not correctly display the remaining time for certain background tasks.

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)

  • QTS 4.3.4.0695 build 20180830 Release Notes


    [Important Notes]
    - This QTS update changes the file system of the system partition to ext4 for ARM-based models with Annapurna Labs processors. For data security reasons, you are not able to downgrade QTS to a previous version after this update.
    Affected models: TS-131P, TS-231P, TS-431P, TS-531P, TS-231+, TS-431+, TS-231P2, TS-431P2, TS-431X, TS-431X2, TS-531X, TS-831X, TS-1231XU-RP, TS-1231XU, TS-831XU-RP, TS-831XU, TS-431XU-RP, TS-431XU, TS-431XeU, and TS-1635.


    - To ensure system stability, QNAP recommends updating and then restarting QVPN Service in App Center after you update QTS to 4.3.4.


    - As QTS previous versions of ARM models do not support snapshots, when you upgrade to QTS 4.3.4, the original volume cannot use this feature immediately. To solve this problem, you have to back up the existing data on your QNAP NAS to external storage. Then you can rebuild the QNAP NAS and take snapshots to the new storage pool with multiple volumes.


    - QTS 4.3.4 is the final available firmware update for the following models:
    TS-EC1679U-SAS-RP, TS-EC1679U-RP, TS-1679U-RP, TS-EC1279U-SAS-RP, TS-EC1279U-RP, TS-1279U-RP, TS-1079 Pro, TS-EC879U-RP, TS-879U-RP, TS-1270U-RP, TS-870U-RP, TS-470U-RP, TS-470U-SP, TS-1269U-RP, TS-869U-RP, TS-469U-RP, TS-469U-SP, TS-879 Pro, TVS-870, TS-870 Pro, TS-870, TVS-670, TS-670 Pro, TS-670, TVS-470, TS-470 Pro, TS-470, TS-869 Pro, TS-869L, TS-669 Pro, TS-669L, TS-569 Pro, TS-569L, TS-469 Pro, TS-469L, TS-269 Pro, TS-269L, IS-400 Pro.


    - For the status of QTS updates and maintenance for your NAS model, visit https://www.qnap.com/en/product/eol.php


    - When QTS 4.3.x is installed on NAS models running on 64-bit Intel and AMD processors, some applications may not be supported. To check if installed apps on your NAS are compatible with QTS 4.3.x, download the QTS 64-bit compatibility tool and install it on your current QTS build. (https://download.qnap.com/QPKG/CF64_0.1-1114.qpkg.zip)


    - Starting from QTS 4.3.4, QNAP NAS devices no longer support creating storage pools or static volumes using NVMe PCIe/M.2 SSDs. However, this limitation does not apply to the SSDs installed in built-in M.2 slots or on QM2 expansion cards.


    - Below are the kernel versions for the NAS models supported by "QTS 4.3.4.0695":


    kernel 3.10.20: TS-128, TS-228
    kernel 3.2.26: TS-x31, TS-x31U
    kernel 3.4.6: TS-x69, TS-x69U, TS-x69L
    kernel 4.2.8: HS-251, IS-400, SS-x79U, TS-x79, TS-x79U, TS-x70, TS-x70U, TVS-x70, TS-x31P, TS-x31P2, TS-x31+, TS-x31X, TS-x31XU, TS-x28A, TS- x35, TS-x51, TS-x51A, TS-x51U, TS-x53, TS-x53A, TBS-x53A, TS-x53B, TS-x53BU, TS-x53S, IS-453S, TS-x53U, TVS-x63, TS-x63, TS-x63U, TS-x73U, TS-x77, TVS-x80, TS-x80, TVS-x80U, TS-x80U, TVS-x82, TVS-x82S, TVS-1582TU, TS-x85, TES-x85U, TDS-16489U, TVS-x71, TVS-x71U, TVS-x73


    [Fixed Issues]
    - Fixed a vulnerability in Samba to address insufficient validation on the client directory (CVE-2018-10858).
    - Fixed a vulnerability in Samba to prevent the disclosure of confidential information from the Active Directory LDAP server (CVE-2018-10919).
    - The MAC address of network interfaces would change unexpectedly after users updated QTS to 4.3.4_20180810 on the TS-x31P.
    - The button string in File Station for creating share links was misplaced in Dutch.
    - In File Station, users could not send a share link via email from the local computer.
    - Users could not connect to a WebDAV server using Remote Mount in File Station.
    - The button string in File Station for creating share links was misplaced in Dutch.
    - The NAS would sometimes restart unexpectedly when users transferred files between two iSCSI LUNs.
    - Connecting an external eSATA disk to the NAS would cause QTS to stop responding.
    - Backup speeds were slower than expected when users backed up data to an external storage device connected to the NAS via StorageCraft ShadowProtect SPX.
    - The NAS would sometimes restart unexpectedly when users frequently transferred files to shared folders via Samba.
    - The speeds of file transfer from the NAS to NTFS external disks were slower than expected.
    - Users could not access exFAT disks after updating QTS to 4.3.4.0644_20180710 on the TS-x69 models.
    - QTS would stop responding after users performed a file system check if users accessed QTS on macOS High Sierra 10.13.6.
    - Users could not access QTS after connecting an external eSATA disk to the NAS.
    - Users could not access the NAS shared folders on Windows Server 2008 R2 after joining the NAS to a domain.
    - Users could not correctly configure DNS settings to resolve domain names after enabling Domain Controller.
    - QTS could not display correct memory information in Control Panel > System Status > Hardware Information after users installed certain Transcend memory modules.
    - Users could not successfully migrate shared folders on an encrypted volume.
    - The write speeds on NTFS external disks were slower than expected after users updated QTS to 4.3.4.0644.
    - QTS could not detect some constituent disks in RAID groups after users updated QTS to 4.3.4.0675 on certain models.
    - Users could not restore files whose filenames contained the slash character (/) from a snapshot if the files were created in a shared folder mounted via AFP.

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)

  • QTS 4.3.4.0734 build 20181008


    [Important Notes]
    This QTS update changes the file system of the system partition to ext4 for ARM-based models with Annapurna Labs processors. For data security reasons, you are not able to downgrade QTS to a previous version after this update.
    Affected models: TS-131P, TS-231P, TS-431P, TS-531P, TS-231+, TS-431+, TS-231P2, TS-431P2, TS-431X, TS-431X2, TS-531X, TS-831X, TS-1231XU-RP, TS-1231XU, TS-831XU-RP, TS-831XU, TS-431XU-RP, TS-431XU, TS-431XeU, and TS-1635.
    To ensure system stability, QNAP recommends updating and then restarting QVPN Service in App Center after you update QTS to 4.3.4.
    As QTS previous versions of ARM models do not support snapshots, when you upgrade to QTS 4.3.4, the original volume cannot use this feature immediately. To solve this problem, you have to back up the existing data on your QNAP NAS to external storage. Then you can rebuild the QNAP NAS and take snapshots to the new storage pool with multiple volumes.
    QTS 4.3.4 is the final available firmware update for the following models:
    TS-1269U-RP, TS-869U-RP, TS-469U-RP, TS-469U-SP, TS-869 Pro, TS-869L, TS-669 Pro, TS-669L, TS-569 Pro, TS-569L, TS-469 Pro, TS-469L, TS-269 Pro, TS-269L.
    For the status of QTS updates and maintenance for your NAS model, visit https://www.qnap.com/en/product/eol.php
    When QTS 4.3.x is installed on NAS models running on 64-bit Intel and AMD processors, some applications may not be supported. To check if installed apps on your NAS are compatible with QTS 4.3.x, download the QTS 64-bit compatibility tool and install it on your current QTS build. (https://download.qnap.com/QPKG/CF64_0.1-1114.qpkg.zip)
    Starting from QTS 4.3.4, QNAP NAS devices no longer support creating storage pools or static volumes using NVMe PCIe/M.2 SSDs. However, this limitation does not apply to the SSDs installed in built-in M.2 slots or on QM2 expansion cards.
    Below are the kernel versions for NAS models that are supported by QTS 4.3.4:
    Kernel 3.10.20: TS-128, TS-228
    Kernel 3.2.26: TS-x31, TS-x31U
    Kernel 3.4.6: TS-x69, TS-x69U, TS-x69L
    Kernel 4.2.8: all other models supported by QTS 4.3.4
    [New feature]
    Added a shared folder backup option. This addresses a known issue in macOS High Sierra 10.13.4 and later versions that prevented QTS users from using Time Machine to back up data from their Mac to their QNAP NAS through SMB shared folders.
    [Fixed Issues]
    Removing or disconnecting a disk from a RAID group during Predictive S.M.A.R.T. Migration might sometimes cause data corruption after the rebuilding.
    Undeletable snapshots would occasionally appear on certain storage pools.
    Music Station would incorrectly display the length of the last track on a list.
    Deleted files would still appear in @Recycle folders even when users disabled Network Recycle Bin.
    Certain processes would sometimes keep using CPU resources.
    RAID groups could not enter degraded mode after users took snapshots and then remove a component disk.
    The TS-x69 would occasionally stop responding after running out of memory.
    Files in a shared folder mounted on macOS via NFS would display incorrect creation dates.
    Users sometimes could not set the NAS as an additional domain controller.
    The NAS time zone would be changed to GMT +0 after users enabled LDAP Server.
    A certain snapshot-related process would use more memory resources than expected.
    A certain snapshot-related process would use more CPU resources than expected.
    QTS could not correctly display domain users' folder permissions inherited from their user groups.
    QTS would not provide relevant notifications when users could not enable Domain Controller due to the system default gateway not being correctly configured.
    General users could still access @Recycle folders even when the access to Network Recycle Bin was only granted to administrators.
    Users could not join the NAS to an Active Directory domain after enabling Domain Controller.
    Users could not create a subfolder or file in a shared folder mounted via SMB in Windows 10.
    QTS occasionally would not automatically mount volumes after the NAS restarted.
    Users could not restore file-based LUNs from snapshots.
    Snapshot restoring tasks would still run in the background even after the NAS restarted.
    It would take longer than expected to authenticate user connections to NFS shared folders.
    Users could not restore a domain controller database from a backup file on an encrypted system volume。
    Users could not save Microsoft Excel files to a shared folder mounted via AFP on macOS.

    Grüße
    ...jp


    DM900 / OE2.5 Experimental ... und sehr glücklich damit :)