rescue mode dm 900uhd

  • hello
    my dreambox I flash dmm or gimini after rebot rescue mode


    CPU 01
    Dreambox DM900
    AVS init...
    AVS init OK
    AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00
    AVS load_code offset =00051000
    LOADED
    AVS: overtemp mon ON


    single board
    select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500
    MEMSYS-STD
    SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0
    MCB: FLEX
    AVS start:status=000000ff
    STB: Current voltage=00000381(897)
    temperature=00009dd7(40407)
    PV=00000344(836)
    MV=0000037e(894)
    AVS FW rev=30333278 [0.3.2.x]
    OK
    DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK
    DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK
    Sdram Scramble OTP = 0x00000001
    Sdram Scramble OK
    select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b
    BFW load mode OTP = 0x0000000f
    bfw_hash_locked = 0x00000000
    BFW key3 OK, BFW load OK
    BFW v2.1.0
    COPY CODE... DONE
    MICH: disable success
    SSBL
    PINMUX
    CACHE FLUSH OK
    MMU ON
    CACHE FLUSH OK
    _fbss 07080cd0
    _ebss 0713dd70
    _end 0713dd90
    HEAP @ 07200000
    STACK @ 09300000
    ARCH: CONFIG OK
    CLR BSS 07080cd0 to 0713dd70 OK
    CLR SRAM OK
    CACHE FLUSH OK
    CPU CLKSET OK
    GO!


    ,/
    ,'/___, BOLT v1.18 v1.18 LOCAL BUILD
    .'__ ,' (2016-12-01 16:24:31 cynric@cynric-VirtualBox)
    /,' Copyright (C) 2016 Broadcom
    /'


    Board: BCM97252SSFF
    SYS_CTRL: product=72521, family=7439b1, strap=000000b2,
    otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)
    otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)
    CPU: 2x B15 [420f00f3] 1719 MHz
    SCB: 432 MHz
    DDR0 @ 1067MHz, DDR1 @ 1067MHz
    RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)
    CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages
    EMMC1: transfer complete intr error, intr=0x208000
    Command 8 failed
    EMMC1: device failed to enter transfer mode
    CS1: NAND: unrecognized ID: 0xffff 0xffffffff
    RTS0: 0x1101004, 256 clients, ok
    RTS1: 0x1181004, 256 clients, ok
    BOX MODE: 5
    card if inited
    set pwm to 0/255
    disp id 5420
    load image
    AVS: park check
    AVS: temperature monitoring enabled
    AVS: STB: V=0.896V, T=+42.355C, PV=0.836V, MV=0.894V, FW=30333278 [0.3.2.x]
    USB otp=00000040
    USB @ 0xf0470200: IPP is active low, IOC is negative polarity
    init fp
    found card in unknown state
    ca valid!
    set pwm to 200/255
    Normal bootup
    Default boot device not found!
    Booting failed. Running recovery
    Loader:zimg Filesys:raw Dev:flash0.recovery File: Options:(null)
    Reading 11632552 bytes from zImage...........
    Starting program at 0x8000 (DTB @ 0x7716000)


    32 bit boot...
    Uncompressing Linux... done, booting the kernel.
    [ 0.000000] Booting Linux on physical CPU 0x0
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.14-1.15-dm900 (dm900@opendreambox.org) (gcc version 5.3.0 (GCC) ) #2 SMP Mon May 1 07:51:45 UTC 2017
    [ 0.000000] CPU: ARMv7 Processor [420f00f3] revision 3 (ARMv7), cr=30c7387d
    [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
    [ 0.000000] Machine model: BCM97252SSFF
    [ 0.000000] moving dtb from 0x0000000007716000 to 0x0000000000f49d70
    [ 0.000000] bmem: Reserved 640 MiB at 0x0000000018000000
    [ 0.000000] bmem: Reserved 384 MiB at 0x0000000080000000
    [ 0.000000] cma: Reserved 16 MiB at 0x000000000f000000
    [ 0.000000] Memory policy: Data cache writealloc
    [ 0.000000] MCP: Enabling write pairing
    [ 0.000000] PERCPU: Embedded 8 pages/cpu @cdfc0000 s9024 r8192 d15552 u32768
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 523776
    [ 0.000000] Kernel command line: bmem=640M@384M bmem=384M@2048M console=ttyS0,1000000 root=/dev/mmcblk0p2 rootwait rootfstype=ext4 coherent_pool=2M
    [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
    [ 0.000000] Memory: 999664K/2097152K available (6110K kernel code, 214K rwdata, 1588K rodata, 7496K init, 208K bss, 1081104K reserved, 16384K cma-reserved, 786428K highmem)
    [ 0.000000] Virtual kernel memory layout:
    [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
    [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
    [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
    [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
    [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
    [ 0.000000] .text : 0xc0008000 - 0xc078cb24 (7699 kB)
    [ 0.000000] .init : 0xc078d000 - 0xc0edf340 (7497 kB)
    [ 0.000000] .data : 0xc0ee0000 - 0xc0f15a60 ( 215 kB)
    [ 0.000000] .bss : 0xc0f15a68 - 0xc0f49d70 ( 209 kB)
    [ 0.000000] Hierarchical RCU implementation.
    [ 0.000000] Additional per-CPU info printed with stalls.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
    [ 0.000000] NR_IRQS:16 nr_irqs:16 16
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc403000, parent irq: 93)
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc3e1000, parent irq: 64)
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc410640, parent irq: 95)
    [ 0.000000] irq_brcmstb_l2: registered L2 intc (mem: 0xfc4d1200, parent irq: 58)
    [ 0.000000] Architected cp15 timer(s) running at 27.00MHz (virt).
    [ 0.000003] sched_clock: 56 bits at 27MHz, resolution 37ns, wraps every 2545165795328ns
    [ 0.000008] Switching to timer-based delay loop
    [ 0.000236] Console: colour dummy device 80x30
    [ 0.000256] Calibrating delay loop (skipped), value calculated using timer frequency.. 54.00 BogoMIPS (lpj=27000)
    [ 0.000265] pid_max: default: 32768 minimum: 301
    [ 0.000358] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.000365] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
    [ 0.005776] Initializing cgroup subsys devices
    [ 0.005790] Initializing cgroup subsys freezer
    [ 0.005797] Initializing cgroup subsys net_cls
    [ 0.005824] CPU: Testing write buffer coherency: ok
    [ 0.006045] CPU0: update cpu_power 1024
    [ 0.006051] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
    [ 0.006101] Setting up static identity map for 0x5d4590 - 0x5d45e8
    [ 0.007316] CPU1: Booted secondary processor
    [ 0.007335] CPU1: update cpu_power 1024
    [ 0.007337] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
    [ 0.007433] Brought up 2 CPUs
    [ 0.007442] SMP: Total of 2 processors activated.
    [ 0.007447] CPU: All CPU(s) started in SVC mode.
    [ 0.007825] devtmpfs: initialized
    [ 0.011357] VFP support v0.3: implementor 42 architecture 4 part 00 variant 0 rev 0
    [ 0.011910] regulator-dummy: no parameters
    [ 0.012102] NET: Registered protocol family 16
    [ 0.013021] DMA: preallocated 2048 KiB pool for atomic coherent allocations
    [ 0.013223] cpuidle: using governor ladder
    [ 0.013227] cpuidle: using governor menu
    [ 0.014366] irq: no irq domain found for /rdb/interrupt-controller@f040a700 !
    [ 0.014448] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
    [ 0.016132] syscon f0404000.syscon: regmap [mem 0xf0404000-0xf0404523] registered
    [ 0.016207] syscon f03e2400.syscon: regmap [mem 0xf03e2400-0xf03e27ff] registered
    [ 0.016273] syscon f0452000.syscon: regmap [mem 0xf0452000-0xf04520ff] registered
    [ 0.016339] syscon f0404100.syscon: regmap [mem 0xf0404100-0xf040415b] registered
    [ 0.016402] syscon f040415c.syscon: regmap [mem 0xf040415c-0xf040419b] registered
    [ 0.016467] syscon f0410700.syscon: regmap [mem 0xf0410700-0xf041070b] registered
    [ 0.016532] syscon f041070c.syscon: regmap [mem 0xf041070c-0xf0410713] registered
    [ 0.016594] syscon f1101004.syscon: regmap [mem 0xf1101004-0xf1101403] registered
    [ 0.016657] syscon f1181004.syscon: regmap [mem 0xf1181004-0xf1181403] registered
    [ 0.016728] syscon f0404080.syscon: regmap [mem 0xf0404080-0xf0404083] registered
    [ 0.016794] syscon f04040a4.syscon: regmap [mem 0xf04040a4-0xf04040a7] registered
    [ 0.016858] syscon f03e0154.syscon: regmap [mem 0xf03e0154-0xf03e0157] registered
    [ 0.016919] syscon f03e0354.syscon: regmap [mem 0xf03e0354-0xf03e0357] registered
    [ 0.016985] syscon f03e0400.syscon: regmap [mem 0xf03e0400-0xf03e0403] registered
    [ 0.017303] irq: no irq domain found for /rdb/interrupt-controller@f0417380 !
    [ 0.017529] Broadcom Brahma-B15 readahead cache at: 0xfc3e2478
    [ 0.021887] bio: create slab <bio-0> at 0
    [ 0.022183] brcmstb-gpio f040a600.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
    [ 0.022210] brcmstb-gpio f040a600.gpio: Registered 5 banks (GPIO(s): 0-159)
    [ 0.022237] brcmstb-gpio f0417400.gpio: Couldn't get IRQ. Enable CONFIG_BCM7120_L2_IRQ if you want GPIO interrupt support
    [ 0.022250] brcmstb-gpio f0417400.gpio: Registered 2 banks (GPIO(s): 160-223)
    [ 0.022600] SCSI subsystem initialized
    [ 0.022810] usbcore: registered new interface driver usbfs
    [ 0.022839] usbcore: registered new interface driver hub
    [ 0.022896] usbcore: registered new device driver usb
    [ 0.022915] media: Linux media interface: v0.10
    [ 0.022941] Linux video capture interface: v2.00
    [ 0.022979] pps_core: LinuxPPS API ver. 1 registered
    [ 0.022983] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
    [ 0.022993] PTP clock support registered
    [ 0.023223] Advanced Linux Sound Architecture Driver Initialized.
    [ 0.023509] Bluetooth: Core ver 2.18
    [ 0.023525] NET: Registered protocol family 31
    [ 0.023528] Bluetooth: HCI device and connection manager initialized
    [ 0.023537] Bluetooth: HCI socket layer initialized
    [ 0.023543] Bluetooth: L2CAP socket layer initialized
    [ 0.023549] Bluetooth: SCO socket layer initialized
    [ 0.023948] Switched to clocksource arch_sys_counter
    [ 0.023958] cfg80211: Calling CRDA to update world regulatory domain
    [ 0.028270] thermal thermal_zone0: failed to read out thermal zone 0
    [ 0.028354] NET: Registered protocol family 2
    [ 0.028740] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.028758] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
    [ 0.028780] TCP: Hash tables configured (established 2048 bind 2048)
    [ 0.028813] TCP: reno registered
    [ 0.028820] UDP hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.028831] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
    [ 0.028963] NET: Registered protocol family 1
    [ 0.029189] RPC: Registered named UNIX socket transport module.
    [ 0.029195] RPC: Registered udp transport module.
    [ 0.029198] RPC: Registered tcp transport module.
    [ 0.029201] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 0.248178] futex hash table entries: 512 (order: 3, 32768 bytes)
    [ 0.248533] bounce pool size: 64 pages
    [ 0.249099] NFS: Registering the id_resolver key type
    [ 0.249137] Key type id_resolver registered
    [ 0.249141] Key type id_legacy registered
    [ 0.249151] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
    [ 0.249289] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
    [ 0.249590] msgmni has been set to 448
    [ 0.250301] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
    [ 0.250309] io scheduler noop registered
    [ 0.250327] io scheduler cfq registered (default)
    [ 0.250553] brcm-gisb-arb f0400000.gisb-arb: registered mem: fc400000, irqs: 258, 259
    [ 0.250844] brcm-usb-phy f0470200.usb-phy: USB3.0 clock not found in Device Tree
    [ 0.316242] brcmstb_memc f1102000.memc-ddr: registered
    [ 0.316270] brcmstb_memc f1182000.memc-ddr: registered
    [ 0.316478] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.317290] f040a900.serial: ttyS0 at MMIO 0xf040a900 (irq = 107, base_baud = 5062500) is a 16550A
    [ 0.413790] console [ttyS0] enabled
    [ 0.415037] loop: module loaded
    [ 0.415679] ahci brcmstb-ahci.0: can't get clock
    [ 0.416302] ahci brcmstb-ahci.0: SSS flag set, parallel bus scan disabled
    [ 0.427963] ahci brcmstb-ahci.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl platform mode
    [ 0.428960] ahci brcmstb-ahci.0: flags: 64bit ncq sntf stag pm clo pmp slum part
    [ 0.431650] scsi0 : ahci_platform
    [ 0.432276] scsi1 : ahci_platform
    [ 0.432778] ata1: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x100 irq 91
    [ 0.433696] ata2: SATA max UDMA/133 mmio [mem 0xf045a000-0xf045aa9b] port 0x180 irq 91
    [ 0.435137] spi_brcmstb f03e3400.spi: 1-lane output, 3-byte address
    [ 0.435905] spi_brcmstb f03e3400.spi: master is unqueued, this is deprecated
    [ 0.439254] m25p80 spi32766.0: found mx25l25635e, expected m25p80
    [ 0.439982] spi_brcmstb f03e3400.spi: 1-lane output, 4-byte address
    [ 0.440724] m25p80 spi32766.0: mx25l25635e (32768 Kbytes)
    [ 0.441377] 5 ofpart partitions found on MTD device spi32766.0
    [ 0.442057] Creating 5 MTD partitions on "spi32766.0":
    [ 0.442655] 0x000000000000-0x000000200000 : "flash0.bolt"
    [ 0.443811] 0x000000200000-0x000000220000 : "flash0.nvram"
    [ 0.444887] 0x000000220000-0x000000240000 : "flash0.devtree"
    [ 0.445947] 0x000000240000-0x000001000000 : "flash0.recovery"
    [ 0.447012] 0x000000000000-0x000002000000 : "flash0"
    [ 0.448329] libphy: Fixed MDIO Bus: probed
    [ 0.448933] tun: Universal TUN/TAP device driver, 1.6
    [ 0.449526] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    [ 0.450580] bcmgenet f0b00000.ethernet: GENET 4.5 EPHY: 0x1001
    [ 0.463952] libphy: bcmgenet MII bus: probed
    [ 0.486805] xhci-brcm: xHCI BRCM driver
    [ 0.487347] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
    [ 0.488020] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 1
    [ 0.489184] xhci-brcm f0471000.xhci_v2: irq 149, io mem 0xf0471000
    [ 0.490058] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.490837] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.491674] usb usb1: Product: xHCI Host Controller
    [ 0.492241] usb usb1: Manufacturer: Linux 3.14-1.15-dm900 xhci-hcd
    [ 0.492965] usb usb1: SerialNumber: f0471000.xhci_v2
    [ 0.493857] hub 1-0:1.0: USB hub found
    [ 0.494318] hub 1-0:1.0: config failed, hub doesn't have any ports! (err -19)
    [ 0.495251] xhci-brcm f0471000.xhci_v2: xHCI Host Controller
    [ 0.495910] xhci-brcm f0471000.xhci_v2: new USB bus registered, assigned bus number 2
    [ 0.496934] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
    [ 0.497721] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.498556] usb usb2: Product: xHCI Host Controller
    [ 0.499123] usb usb2: Manufacturer: Linux 3.14-1.15-dm900 xhci-hcd
    [ 0.499832] usb usb2: SerialNumber: f0471000.xhci_v2
    [ 0.500683] hub 2-0:1.0: USB hub found
    [ 0.501143] hub 2-0:1.0: 2 ports detected
    [ 0.501910] ehci-brcm: EHCI BRCM driver
    [ 0.502438] ehci-brcm f0470300.ehci_v2: EHCI Host Controller
    [ 0.503109] ehci-brcm f0470300.ehci_v2: new USB bus registered, assigned bus number 3
    [ 0.514124] ehci-brcm f0470300.ehci_v2: irq 145, io mem 0xf0470300
    [ 0.519956] ehci-brcm f0470300.ehci_v2: USB 2.0 started, EHCI 1.00
    [ 0.520761] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.521549] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.522384] usb usb3: Product: EHCI Host Controller
    [ 0.522951] usb usb3: Manufacturer: Linux 3.14-1.15-dm900 ehci_hcd
    [ 0.523660] usb usb3: SerialNumber: f0470300.ehci_v2
    [ 0.524509] hub 3-0:1.0: USB hub found
    [ 0.524970] hub 3-0:1.0: 1 port detected
    [ 0.525616] ehci-brcm f0470500.ehci_v2: EHCI Host Controller
    [ 0.526284] ehci-brcm f0470500.ehci_v2: new USB bus registered, assigned bus number 4
    [ 0.537283] ehci-brcm f0470500.ehci_v2: irq 146, io mem 0xf0470500
    [ 0.543953] ehci-brcm f0470500.ehci_v2: USB 2.0 started, EHCI 1.00
    [ 0.544754] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
    [ 0.544961] ata1: SATA link down (SStatus 0 SControl 300)
    [ 0.546161] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.547000] usb usb4: Product: EHCI Host Controller
    [ 0.547562] usb usb4: Manufacturer: Linux 3.14-1.15-dm900 ehci_hcd
    [ 0.548277] usb usb4: SerialNumber: f0470500.ehci_v2
    [ 0.549202] hub 4-0:1.0: USB hub found
    [ 0.549655] hub 4-0:1.0: 1 port detected
    [ 0.550376] ohci-brcm: OHCI BRCM driver
    [ 0.550890] ohci-brcm f0470400.ohci_v2: BRCM OHCI controller
    [ 0.551559] ohci-brcm f0470400.ohci_v2: new USB bus registered, assigned bus number 5
    [ 0.552484] ohci-brcm f0470400.ohci_v2: irq 147, io mem 0xf0470400
    [ 0.608064] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
    [ 0.608845] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.609680] usb usb5: Product: BRCM OHCI controller
    [ 0.610247] usb usb5: Manufacturer: Linux 3.14-1.15-dm900 ohci_hcd
    [ 0.610962] usb usb5: SerialNumber: f0470400.ohci_v2
    [ 0.611795] hub 5-0:1.0: USB hub found
    [ 0.612263] hub 5-0:1.0: 1 port detected
    [ 0.612906] ohci-brcm f0470600.ohci_v2: BRCM OHCI controller
    [ 0.613577] ohci-brcm f0470600.ohci_v2: new USB bus registered, assigned bus number 6
    [ 0.614496] ohci-brcm f0470600.ohci_v2: irq 148, io mem 0xf0470600
    [ 0.658955] ata2: SATA link down (SStatus 0 SControl 300)
    [ 0.670058] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
    [ 0.670838] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    [ 0.671672] usb usb6: Product: BRCM OHCI controller
    [ 0.672239] usb usb6: Manufacturer: Linux 3.14-1.15-dm900 ohci_hcd
    [ 0.672954] usb usb6: SerialNumber: f0470600.ohci_v2
    [ 0.673776] hub 6-0:1.0: USB hub found
    [ 0.674238] hub 6-0:1.0: 1 port detected
    [ 0.674929] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.675688] ehci-pci: EHCI PCI platform driver
    [ 0.676247] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 0.676963] ohci-pci: OHCI PCI platform driver
    [ 0.677583] usbcore: registered new interface driver usb-storage
    [ 0.678281] i2c /dev entries driver
    [ 0.678729] lirc_dev: IR Remote Control driver registered, major 250
    [ 0.679786] brcmstb_thermal f04d1500.thermal: registered AVS TMON of-sensor driver
    [ 0.680769] usbcore: registered new interface driver btusb
    [ 0.681465] cpufreq_cpu0: failed to get cpu0 regulator: -19
    [ 0.682250] sdhci: Secure Digital Host Controller Interface driver
    [ 0.682967] sdhci: Copyright(c) Pierre Ossman
    [ 0.683469] sdhci-pltfm: SDHCI platform and OF driver helper
    [ 0.685228] mmc0: no vqmmc regulator found
    [ 0.685701] mmc0: no vmmc regulator found
    [ 0.715955] mmc0: SDHCI controller on f03e0000.sdhci [f03e0000.sdhci] using ADMA
    [ 0.717865] mmc1: no vqmmc regulator found
    [ 0.718344] mmc1: no vmmc regulator found
    [ 0.748953] mmc1: SDHCI controller on f03e0200.sdhci [f03e0200.sdhci] using ADMA
    [ 0.749904] hidraw: raw HID events driver (C) Jiri Kosina
    [ 0.750614] usbcore: registered new interface driver usbhid
    [ 0.751261] usbhid: USB HID core driver
    [ 0.753691] TCP: cubic registered
    [ 0.754691] NET: Registered protocol family 10
    [ 0.755672] NET: Registered protocol family 17
    [ 0.756407] Bluetooth: RFCOMM TTY layer initialized
    [ 0.756990] Bluetooth: RFCOMM socket layer initialized
    [ 0.757580] Bluetooth: RFCOMM ver 1.11
    [ 0.758021] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    [ 0.758630] Bluetooth: BNEP filters: protocol multicast
    [ 0.759238] Bluetooth: BNEP socket layer initialized
    [ 0.759809] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
    [ 0.760497] Bluetooth: HIDP socket layer initialized
    [ 0.761113] l2tp_core: L2TP core driver, V2.0
    [ 0.761633] Key type dns_resolver registered
    [ 0.762204] Registering SWP/SWPB emulation handler
    [ 0.763023] regulator-dummy: disabling
    [ 0.765703] ALSA device list:
    [ 0.766056] No soundcards found.
    [ 0.769452] Freeing unused kernel memory: 7496K (c078d000 - c0edf000)
    INIT: version 2.88 booting
    [ 0.820721] mmc1: BKOPS_EN bit is not set
    [ 0.830914] mmc1: new high speed MMC card at address 0001
    [ 0.831876] mmcblk0: mmc1:0001 4FPD3R 3.64 GiB
    [ 0.832546] mmcblk0boot0: mmc1:0001 4FPD3R partition 1 4.00 MiB
    [ 0.833393] mmcblk0boot1: mmc1:0001 4FPD3R partition 2 4.00 MiB
    [ 0.834619] mmcblk0rpmb: mmc1:0001 4FPD3R partition 3 512 KiB
    [ 0.840364] mmcblk0: p1 p2 p3
    Starting udev
    [ 0.843762] mmcblk0boot1: unknown partition table
    [ 0.845044] mmcblk0boot0: unknown partition table
    starting version 230
    [ 0.866265] random: systemd-udevd urandom read with 28 bits of entropy available
    [ 1.198339] bcmdriver: module license 'Proprietary' taints kernel.
    [ 1.199105] Disabling lock debugging due to kernel taint
    [ 1.200129] BCMDRV: Initializing bcmdriver version $ 8
    [ 1.200726] BCMDRV: Total intc words=4,Total Irqs=129
    [ 1.201934] BCMDRV: Initialization complete
    bootlogd: cannot allocate pseudo tty: No such file or directory
    Sun Apr 30 21:28:17 UTC 2017
    INIT: Entering runlevel: 5
    Configuring network interfaces... [ 1.566954] f0b00000.etherne:01: Broadcom BCM7439 (2) PHY revision: 0x10, patch: 1
    [ 1.571549] f0b00000.ethernet: configuring instance for internal PHY
    [ 1.572345] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    udhcpc (v1.24.1) started
    Sending discover...
    [ 3.573065] libphy: f0b00000.etherne:01 - Link is Down
    Sending discover...
    [ 5.532095] libphy: f0b00000.etherne:01 - Link is Up - 1000/Full
    [ 5.532799] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    Sending discover...
    Sending select for 10.0.0.2...
    Lease of 10.0.0.2 obtained, lease time 3600
    /etc/udhcpc.d/50default: Adding DNS 10.0.0.138
    done.
    Starting Dropbear SSH server: Generating key, this may take a while...
    Public key portion is:
    ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCOgswS5X2NPTM+V4Vm0mRiQsI8BC+sCIIPzVqA8s4LlbRTKrh6HnS3qigFCh5/GQiJkY+I8kmabfG6taw0HkrDVAPL3QZyv+T5uuEKLgH/XaJmou7BsccJXe7woLxW/RctnWys/2fA656va4piLN6Yodtys8mEIaLFwqo7/WpVnqdVntam4yMVqMU2yMruMgDYltmTde2QVKxqB8DICwiRoYxgBBOZj7pfDvNkzN/XSpomM1CawINqcvj2/h0/2d29vCMv/hQTdUzKfTIxu/X6nG/Tf0N+D6S6P7OOfOZA5vWxyr9gYy0UXRe5d6OvMSAoSYvHW9UG7gz9EslRoUfz root@dm900
    Fingerprint: md5 e7:e6:d4:65:76:1b:24:5a:65:e1:4e:fe:6c:43:0d:d9
    dropbear.
    Starting autoflashd.
    Starting recovery-ui.
    Starting tpmd.
    [ 10.885936] random: nonblocking pool is initialized
    Starting internet superserver: xinetd.
    Starting Lighttpd Web Server: lighttpd.
    2017-04-30 21:28:26: (../../lighttpd-1.4.39/src/log.c.194) server started


    opendreambox 2.5.0 dm900 /dev/ttyS0


    >>> Your Dreambox has booted into RESCUE MODE.
    >>> Please log in as user 'root' (no password required),
    >>> then run 'help' to get further information.


    dm900 login:

  • problem directory
    Starting udev
    [ 0.843762] mmcblk0boot1: unknown partition table
    [ 0.845044] mmcblk0boot0: unknown partition table

  • Try again but before starting the flash operation do uncheck the option to backup and restore settings. Sorry have no screenshot available to demo the setting I mean but I am sure you will find it.

  • I back update file
    settings.tar.gz
    it not help




    Console log:[*] Mounting '/dev/mmcblk0p2' to '/mnt'
    [*] Remounting '/dev/mmcblk0p3' to '/data'
    [*] Mounting 'tmp' to '/mnt/tmp'
    [*] Creating /data/.recovery/settings.tar.gz from /mnt
    [*] Unmounting '/mnt/tmp'
    [*] Unmounting '/mnt'