[Enigmalight Update-Thread] v0.2rc1 22-01-2015 (IPK and DEB)

  • Zitat

    Original von holymoly
    jep, die Ambilights funkionieren schon mit den Receivern.


    ich meine ob ich es beim normalen Fernsehen nutzen kann (ProSieben etc.) oder ob es nur bei bestimmten Plugins anspringt.


    Zitat

    Original von holymoly
    Ist der cdc-acm Treiber überhaupt aktiv?


    Er ist wohl nicht aktiv. Ich sehe aber das er installiert wurde mit enigmalight zusammen. Beim Versuch den Treiber zu aktivieren bekomm ich ein: "modprobe: FATAL: Module cdc-acm not found."
    Ein erneutes installieren geht nicht, da er mir sagt dass die aktuellste version installiert ist.


    Nach einem Reboot bleibt die Box wie erwartet hängen. Ich kann jedoch per telnet drauf zugreifen und jetzt hab ich nochmal mit lsmod nachgeschaut und das "cdc_acm" Modul ist aktiv...dafür jedoch kein anderes modul!


    Die deinstallation des Moduls bringt nichts, es bleibt beim selben Error wie letztes mal. Kann es sein das der Speicher nicht ausreicht?

  • Zitat

    Original von Luki90


    ich meine ob ich es beim normalen Fernsehen nutzen kann (ProSieben etc.) oder ob es nur bei bestimmten Plugins anspringt.


    Kann es sein das der Speicher nicht ausreicht?


    Ja, klar funktioniert beim TV-Bild und Aufnahmen - würde ja sonst nur wenig Sinn machen!


    Ist die 4000er auf 750 MHz getaktet? Ich kenne niemanden der ein Ambilight mit dieser Box betreibt auch nicht die mindest Anforderungen von Enigmalight. Schreib doch mal den "Speedy" direkt per PN (englisch) an.

  • ... und sorry für die Abwesenheit, aber heute Abend bin ich wieder Online.


    Japs, bei meiner et8000 / 4.2 openATV ist der cdc-acm über putty zu sehen. Aber ich bekomme es einfach nicht zum laufen, obwohl ich alles neu installiert habe sowie die config neu erstellt. Irgenwie steht was in der log.file das man die alte enigmalight.gui löschen soll.


    Beim Netzwerk: Welche IP und NUmmer gebt Ihr denn an? ... obwohl ja holymoly empfiehlt, dass man "Netzwerk Funktion" deaktivieren soll, oder hab ich da was falsch verstanden?


    Vielleicht beheben sich ja die Fehler, wenn die config-Funktion in den Einstellungen freigeschaltet werden, und das Plugin "Enigmalight" selber die config schreiben kann, oder nicht. ... vieleicht sollte ich mal die lese und schreibrechte überprüfen ... 755?


    So, muß jetzt wieder in Krankenhaus aber bin heute Abend wieder Online :)


    Danke liebe Community und schön das es solche Leute wie speedy, holymoly, ... gibt, DANKE!


    ps
    soll man lieber in englisch schreiben oder ist deutsch ok?


  • Mit dem Netzwerkmodus hab ich auch mal rumgespielt, danach lies er sich nicht mehr deaktivieren - habe dann einfach mein Backup wieder aufgespielt. Vielleicht auch mal die enigma "settings" von den enigmalight Einträgen säubern (das speichern funktioniert aber erst nach putty "init 4").
    Du könntest ja mal Deine config hier posten (oben code einfügen button auswählen)

  • gibts schon was Neues zur Einstellung der schwarzen Balkenerkennung?


    Das Ambilight kommt bei den meisten Filmen nicht so gut rüber.

  • Leider nein!
    Meine Empfehlung war ja zwei configs zu erstellen - eine normale und eine
    tiefschauende (über die Balken hinaus).

  • Hello, yesterday I mounted the leds and arduino.
    I can connect the arduino ide to mainboard arduino and program it.
    The leds turn on rgb.


    After, I installed the enigmalight in the Gigablue, and after I reboot system.


    I connect the leds, arduino to gigablue. If enter into plugin menu I can enter in enigmalight plugin, and after, when I press the green button for activate the leds turn on rgb and after the leds always turn on in white color.


    I think that my enigmalight.conf is not good configured.


    The leds are ws2801, and arduino uno.
    I mount 39 leds for 42" TV


    I Calculate the prefix with:
    /home/elight-addons/prefix 39
    I suppose that 39 is the leds for me. I read this in previus page but 39 instead 92. It's ok?


    My config file is this:


    Someone can help me?
    I am new user from this plugin.


    Sorry if my english is bad.


    Regard.

  • Hi , prefix is right, but your [light] is wrong. It must goint till ambilight 117


    Sorry i'am busy in moment.

  • Zitat

    Original von holymoly
    Hi , prefix is right, but your [light] is wrong. It must goint till ambilight 117


    Sorry i'am busy in moment.


    Thank you.
    I change my enigmalight.conf but the error is the same.


    It's now ok?


  • Zitat

    Originally posted by holymoly
    hi,
    try this.


    #interface 127.0.0.1


    or write a PM to "speedyisfast" :)


    Thank you.
    I can probe comment this line and the results are similar.
    When I press green button, rgb test but after all leds off.


    I write a MP to Speedy.

  • Zitat

    Originally posted by jarro_25


    Thank you.
    I can probe comment this line and the results are similar.
    When I press green button, rgb test but after all leds off.


    I write a MP to Speedy.


    I can't send mp, I don't know if the minimun off mesages is 10 for write mp?


    last lines of Log program:


    Traceback (most recent call last):
    File "/usr/lib/enigma2/python/Components/ActionMap.py", line 48, in action
    File "/usr/lib/enigma2/python/Plugins/Extensions/EnigmaLight/EL_PathSelector.py", line 113, in up
    self.updateTarget()
    File "/usr/lib/enigma2/python/Plugins/Extensions/EnigmaLight/EL_PathSelector.py", line 149, in updateTarget
    currFile = self.filelist.getCurrentDirectory() + self.filelist.getFilename()
    TypeError: cannot concatenate 'str' and 'NoneType' objects
    (PyObject_CallObject(<bound method ActionMap.action of <Components.ActionMap.ActionMap instance at 0x260c058>>,('WizardActions', 'up')) failed)


    Thanks

  • hi iam testing the beta 0.1r5-b11
    it works very good on solo2 but lights don't turn off. on stanby mode
    and not detecting blackbars.
    here is my enigmalight.conf file if any help.
    thanks.


    [global]


    [device]
    name ambilight
    channels 30
    type lightpack
    interval 20000
    #serial 649323139323515111C0

    #bus 1
    #address 6
    #debug true


    [color]
    name red
    rgb FF0000


    [color]
    name green
    rgb 00FF00


    [color]
    name blue
    rgb 0000FF


    #bottom
    [light]
    name xx1
    color red ambilight 1
    color green ambilight 2
    color blue ambilight 3
    hscan 50 100
    vscan 95 100


    #bottom
    [light]
    name xx2
    color red ambilight 4
    color green ambilight 5
    color blue ambilight 6
    hscan 0 50
    vscan 95 100


    #left
    [light]
    name xx3
    color red ambilight 7
    color green ambilight 8
    color blue ambilight 9
    hscan 0 5
    vscan 0 50


    #left
    [light]
    name xx4
    color red ambilight 10
    color green ambilight 11
    color blue ambilight 12
    hscan 0 5
    vscan 50 100


    #top
    [light]
    name xx5
    color red ambilight 13
    color green ambilight 14
    color blue ambilight 15
    hscan 0 25
    vscan 0 5


    #top
    [light]
    name xx6
    color red ambilight 16
    color green ambilight 17
    color blue ambilight 18
    hscan 25 50
    vscan 0 5


    #top
    [light]
    name xx7
    color red ambilight 19
    color green ambilight 20
    color blue ambilight 21
    hscan 50 75
    vscan 0 5


    #top
    [light]
    name xx8
    color red ambilight 22
    color green ambilight 23
    color blue ambilight 24
    hscan 75 100
    vscan 0 5


    #right
    [light]
    name xx9
    color red ambilight 25
    color green ambilight 26
    color blue ambilight 27
    hscan 95 100
    vscan 50 100


    #right
    [light]
    name x10
    color red ambilight 28
    color green ambilight 29
    color blue ambilight 30
    hscan 95 100
    vscan 0 50

  • Hi,
    I had problems getting enigmalight to work with et8000 and openatv 4.2. Whenever I installed enigmalight the box would not start up again and hang at the xtrend logo.


    The good news is: I finally got it working. Here is what I dd:
    1. updated openpli software to latest version (Einstellungen->software Management->Software Aktualisieren)
    2. logged onto the box per telnet
    3. I knew enigmalight depends on libusb, cdc-acm, ftdi-sio, usbserial modules.
    So I checked those: opkg list-installed | grep libusb
    libusb was already installed
    4. I had to add kernel-module-cdc-acm: opkg install kernel-module-cdc-acm
    5. I verified the kernel module: modprobe cdc-acm
    6. and checked: modinfo cdc-acm
    all looked ok.
    7. I rebooted the box through the menu
    8. box came up OK and I first did a manual backup
    9. now logged in through telnet again, went to my directory I uploaded the ipk file to and installed enigmalight: opkg install enigma2-plugin-extensions-enigmalight_0.1r5-b10_all.ipk
    10. copied my old boblight.conf file: cp boblight.conf /etc/enigmalight.conf
    11. rebooted the box once more
    12. it came up, so I did another backup
    13. enigmalight could be activated and lights came on by going to: Erweiterungen->Enigmalight
    and then pressing the green button for "Lights on"


    Now I am happy :)


    Now it would be nice to have one button to activate/deactivate the lights without going to the plugins menu. and it would be nice to be able to change the configuration easily until we have the auto-black-bar-detection :)

  • ouuuuch ... seit 2 Tagen schlage ich mich schon rum und werde noch wahhhhnsinig!


    Bin jetzt von openATV auf openPLI umgestiegen und ärgere mich schon seit Stunden mit 2 Dingen herum:


    1. ENIGMALIGHT will einfach nicht mehr gehen, habe eine neue enigmalight.conf erstellt, jedoch erhalte ich jetzt zumindest eine error Meldung


    Code
    16:30:32 16:30:32   start of log @ //.enigmalight/enigmalight.log
    16:30:32 16:30:32   [Config] opening /etc/enigmalight.conf
    16:30:32 16:30:32   [Config] checking config lines
    16:30:32 16:30:32   ERROR: [Config] /etc/enigmalight.conf line 37 section [light]: name (Left1) must be 3 chars
    16:30:32 16:30:32   ERROR: [Config] /etc/enigmalight.conf line 45 section [light]: name (Left2) must be 3 chars
    16:30:32 16:30:32   ERROR: [Config] /etc/enigmalight.conf line 53 section [light]: name (Left3) must be 3 chars
    16:30:32 16:30:32   ERROR: [Config] /etc/enigmalight.conf line 61 section [light]: name (Left4) must be 3 chars
    
    
    .... errrooooor bis line 397 section


    *wollte hier nichts zumüllen, deshalb habe ich mal abgekürzt:)


    hier meine enigma.conf auf die sich die error Meldungen in der Logfile beziehen:



    Sorry, wie kann ich hier daraus ein Spoiler machen, da ich das Forum nicht zumüllen mag.


    Das 2. Problem ist, das seit dem ich auf openPLI umgestigen bin, will meine cccam nicht mehr entschlüsseln bei kabeld Deutschland. Hat hier vielleicht einen Tip?


    Sorry Jungs, aber ich bin echt am verzweifeln & weiss nicht mehr weiter. Alles hat mit dem doofen update angefangen und jetzt ....


    Danke

  • Er hat Dir doch gesagt was falsch ist!


    Der Licht Name darf nur aus drei Zeichen bestehen.


    falsch: name Top10


    richtig z.B.: name T10


    edit: und setze mal eine # vor interface