[Boblight SupportThread] Update: 11-02-2014, Boblight 0.8R6

  • Quote

    Originally posted by Karalik
    I'm using dm800 and raspberry pi with your latest daemon and 50 ws2801. I'm planning to increase led to 100 but as far as i remember there is restriction with dm800. Is it still valid while using raspi as a daemon?


    I tried 100 Led with dm800 and it worked. (deamon on raspberry pi)

  • Hello,
    I am using a Sundtek DVB-C USB Stick on my DM800se.
    Now I want also a Boblight on the back of my panel with the Sedu Board.


    After installing the boblight plugin every reboot the receiver stucks at 3/4 Loading Balance.
    Can you fix that problem or help me?


    Thank you.


    Dear Martin


  • Hi Speedy,


    did you check that overview? Is it possible, that every receiver in that overview might be compatible with Boblight? The chipsets are familiar.

    VU+ UNO, VTI 5.1.x, 500GB internal HDD, 4GB Stick for PICONS
    Arduino UNO, 50 WS2801 LEDs, Boblight (always the latest version)

  • Is it possible to use scart-input signal (vcr) with boblight?

    Xtrend et9000 mit OpenPLI 4
    SEDUlight
    FreeNAS 9

  • hello,


    now works my boblight with solo2 :)))
    but the colors are sometimes not correct, when i watch football, the grass are not green on led.


    how looks your dynamic adjustment?


    gr

  • Hi,


    my new sedulight always stays in standalone-program. can't find the error. :-( what can i do?


    Edit: its done. working great! trusted the plugin-config-maker. editing by hand helped!


    But now i always get

    Code
    [Boblight] Gamma not set, using 2.2 since this is default for video


    any idea?

    Xtrend et9000 mit OpenPLI 4
    SEDUlight
    FreeNAS 9

    Edited 2 times, last by mrMuppet ().

  • @ MrMuppet: This is a normal message when you use the default gamma. when you start with -o gamma=2.1 , you dont get this message.


    chriss255
    For the colors, play around with the adjust in boblight.conf.
    But restart everytime the daemon to use the new setting.


    Gr speedy. Sorry for late post. i have it verry bussy on this moment with work. :tongue:

    if you like this project and want to support me, buy me a beer ;) Thanks!!

  • Quote

    Originally posted by speedyisfast
    @ MrMuppet: This is a normal message when you use the default gamma. when you start with -o gamma=2.1 , you dont get this message.


    And it's not telling me, that the gamma-settings in boblight.conf isn't correct? Ok. thanks

    Xtrend et9000 mit OpenPLI 4
    SEDUlight
    FreeNAS 9

  • I have the Feeling that the Autostart of the deamon still is not working :rolleyes:


    Without starting it from the console - my lights are not working.


    Isn`t it possible to start the deamon manually from the GUI?


    Lights ON - only starts the grabber I guess,...


    GreeT`s eRich

  • Helped please, I have the VTI OE 1.6. I set enigma2-plugin-extensions-boblight-enigma2_0.7r7_Beta_mipsel.ipk.
    In Putty wrote:
    / etc / init.d / boblight control start.
    On-screen error:
    Start boblight ....
    Checing if Boblight is running: Boblight is not running! starting daemon .....
    / usr / bin / boblightd: error while loading shared libraries: libusb-1.0.so.0: can not open shared object file: No such file or directory
    Starting boblight-enigma2 ........
    ERROR: libusb-1.0.so.0: can not open shared object file: No such file or directory.
    I set manually library libusb-1.0-0_1.0.4-r0_mipsel.
    After that on-screen next:
    ERROR: / usr / lib / libboblight.so: undefined symbol: boblight_fillbuffer
    ERROR: Arduino: / dev/ttyUSB0: open () No such file or directory
    What do Now?

  • I did put a different image on VTI 5.1.0 OE-2
    Set Boblight mipsel32
    When you connect the Arduino blinking LED TX
    Tape 20-25 seconds blinks red.
    At the start of Boblight produces a log, a tape 1 LED blinks red quickly, the next 4-5 colored but quickly faded.
    Libraries libboblight.so in the package is not there libboblight.so.0.0.0
    My actions?


    My Log:
    root@bm750:~# /etc/init.d/boblight-control start
    Checking for boblight pids...

    sh: invalid number ''
    sh: invalid number ''
    sh: invalid number ''
    Start boblight...
    Checking if Boblightd is running: Boblightd is not running! starting deamon....

    Boblightd 2.0 (optimized version for enigma2) (c) 2012-2013 Speedy1985)
    (InitLog) start of log /home/root/.boblight/boblightd.log
    (PrintFlags) starting /usr/bin/boblightd -f
    (CConfig::LoadConfigFromFile) opening /etc/boblight.conf
    (CConfig::CheckConfig) checking config lines
    (CConfig::CheckConfig) config lines valid
    (CConfig::BuildConfig) building config
    (CConfig::BuildConfig) built config successfully
    (main) starting devices
    (CDevice::Process) arduino: starting with output "/dev/ttyACM0"
    (CDevice::Process) arduino: setting up
    (CClientsHandler::Process) opening listening TcpSocket on *:19333
    (CDevice::Process) arduino: setup succeeded
    Starting boblight-enigma2...
    ERROR: libboblight.so: cannot open shared object file: No such file or director

  • And again... ;(


    Does boblight work with a Xtrend 6500 Receiver. It does have the same Chip (BCM7413), same clockrate (400 MHz), same memory (512 MB) as the VU+ UNO.


    Only difference is the 1GB flash memory.


    An answer before the start of the Bundesliga season 2013/14 would be great.


    Thanks in advance.

    VU+ UNO, VTI 5.1.x, 500GB internal HDD, 4GB Stick for PICONS
    Arduino UNO, 50 WS2801 LEDs, Boblight (always the latest version)



  • Hi, Yes Boblight is working on a et6500 receiver.


    Gr Speedy1985

    if you like this project and want to support me, buy me a beer ;) Thanks!!

  • hi all,


    ich bekomm das ding irgendwie nicht zum laufen und bin mit meinem latein am ende...


    könnte mir vlt jemand etwas helfen?


    ach ja, solo2 vti 5.1 boblight 07r7 und sedu


    dank im voraus!


    hier noch ein log:
    root@vusolo2:~# /etc/init.d/boblight-control start
    sh: invalid number ''
    sh: invalid number ''
    sh: invalid number ''
    Checking if Boblightd is running: Boblightd is not running! starting deamon....
    boblightd (c) 2009 bob loosen (compiled for enigma2 - see source for more information)


    (InitLog) start of log /home/root/.boblight/boblightd.log
    (PrintFlags) starting /usr/bin/boblightd -f
    (CConfig::LoadConfigFromFile) opening /etc/boblight.conf
    (CConfig::CheckConfig) checking config lines
    (CConfig::CheckConfig) config lines valid
    (CConfig::BuildConfig) building config
    (CConfig::BuildConfig) built config successfully
    (main) starting devices
    (CClientsHandler::Process) opening listening socket on *:19333
    (CDevice::Process) ambilight: starting with output "/dev/ttyUSB0"
    (CDevice::Process) ambilight: setting up
    (CDevice::Process) ambilight: setup succeeded
    Starting Grabber...
    root@vusolo2:~#
    boblight-enigma2 0.5r15 (c) 2012 Martijn Vos(speedy1985) and c@rstenpresser


    Connecting to boblightd
    (CClientsHandler::Process) 127.0.0.1:43514 connected
    (CClientsHandler::ParseMessage) 127.0.0.1:43514 said hello
    Connection to boblightd opened
    Gamma not set, using 2.2 since this is default for video
    [grabber] found STB-Type 5
    [grabber] Maximum intermediate-picture-size is 128px
    [grabber] Sync mode enabled
    [grabber] Found 64 lights


    (CClientsHandler::ParseSet) 127.0.0.1:43514 priority set to 20
    [grabber] Setting framerate to 25000
    [grabber] Setting Resolution to 90x72 (Source 720x576)
    [grabber] Setting framerate to 50000
    [grabber] Setting framerate to 25000
    [grabber] Setting Resolution to 90x72 (Source 720x576)
    [grabber] Setting framerate to 50000
    [grabber] Setting Resolution to 80x44 (Source 1280x720)




    LG
    Robert

  • Hey Speedy!


    Boblight 0.7R7 is running great on my Solo2.


    But I have noticed some red flashes at my lower right corner (start-point). They occur about every 8-10 seconds and last about 0,5-1sec when the picture is dark/black in this corner. Especially at movie credits.


    Any idea what causes this?


    Greetings, Martin

  • Hi,


    the first light in line starts blinking red every 8-10 sek, when it's getting no signal. Blacklevel set to 30, Sedu-Board




  • Same here. I had that problem in the past, then it was gone, now its back and yesterday I've updated to VTI 6.0 to see if it still happens.


    Without the Sundtek stick, the Box boots just fine. With the stick, it doesn't. If I start the DVB-C stick later, the box will hang up.


    Nightmareachim had the same issue


    I will try to see what happens, if the deamon is stopped and I try to activate the stick again.


    What about an active USB-Hub. In My case, Adalight is connected to a USB Hub, where there is also a mini USB stick for picons. The Sundtek is using the other free USB port.

    VU+ UNO, VTI 5.1.x, 500GB internal HDD, 4GB Stick for PICONS
    Arduino UNO, 50 WS2801 LEDs, Boblight (always the latest version)

    Edited once, last by TheNewGuy ().