Dm600pvr Enigma2 Pcd 7.0

Daemon manager gui has an autostart @ bootup option

Is the version of BarryAllen in this image the latest that can be installed. I don't want to start uninstalling n feck things up just yet!

I ask this as I remember a few additional options in 4.8.22 and the latest version available for PPC is 5.0.17.

Also reading an old simple howto BA I created a while ago I've stumbled across some interesting info, given the dvb-modules date I asked about before.

I found these sources: dreambox-dvb-modules-dm600pvr-2.6.12-20090707.tar.bz2

DM600PVR:
KV_dm600pvr = "2.6.12"
PV_dm600pvr = "${KV}-20090707"

These are the drivers in the last DM image for DM600 to DL from Dream, but I'm pretty sure both cvs n openpli e1 have: PV_dm600pvr = "${KV}-200904030"

This earlier driver caused later versions of BA for ppc to complain about secondstage loader n not install, As I will have to test in the flash image can you offer any advice before I start.

Regards

Hej

Ok i'll try n break it n report back.

So I can install pretty much anythin from the deploy/ipk folder?

Is it a transcoding issue? I've had my fairshare of probs with transcoding for my godson's psp when he goes on holiday.

thats in my tmp/work folder!

where my compiled ipks are

Edit: BA 5.0.17 seems to install over the top of existing version ok.

Edit: dvb-modules seems to have done no damage but don't know if they will do any good.

Edit: openvpn_2.0.2 seems to be running ok, needed updated lib, needs more testing

Quote

Original von Karate01
Hi kalehrl
Hi pcd

The "problem" with BA and HDD is known, due to that I definitively want to install/boot from CF.
At the moment I also have no experience with that but I´ll try.
And I´ll give feedback in both cases (good or bad experiences)

best regards

Display More

Hi,

as promissed I want to give feedback.
Unfortunately at the moment with "bad experiences".

At the moment I fail to "run the CF".
I bought a CF-IDE-adapter.
I bought a new CF-card (30MB/s)
I bought a mini-IDE-44pin cable (three plugs)

But I failed to install BA. (on The CF)
And I even failed to "see" the CF-card listed in the DreamControlCenter
==> So I think it isn´t a BA-problem but a proplem with thd CF or the items in between

But I have no idea why the CF card isn´t shown in DCC.
I tried to format in different ways:
- FAT32 (windows, slow formating process)
- ext2 (formated with ubuntu and with a tool under windows)
- FAT32 (with HP USB Disk Storage Formating Tool)
But everything without success.

I tried "CF only" (only the CF adapted to the cable and I tried "CF and the HDD" (HDD as master and the CF as slave)

Do I have to do something special with the image so that I can use the CF?
What is my mistake?

Thanks for any suggestions.

Quote

Original von pcd
Hi Karate01,

Have you seen this post ? :-

http://www.digitalworldz.co.uk…pactflash-barryallen.html

Does it help ?

Cheers.

Display More

Hi pcd,

I haven´t had until today.
In the meantime I have. [ thanks for the link ! ]
But it didn´t help (really).

I think from the "physically side" I did everything well.
I already tried another CF-Card and another IDE-cable.
The HDD works fine but not the CF-Card.

If I understand the thread right, then it is only necessary to "connect" the items and then everything should be o.k. !?

So that´s my main question:
- Do I have to do something special in the image that the CF-card can be used?
- Do I have to go to a sub-menu to "activate" the CF card?
- Do I have to edit a file?
or
- Should the CF-card appear automatically when the "physical connection" is all right?

Thanks

Quote

Original von Karate01
So that´s my main question:
- Do I have to do something special in the image that the CF-card can be used?
- Do I have to go to a sub-menu to "activate" the CF card?
- Do I have to edit a file?
or
- Should the CF-card appear automatically when the "physical connection" is all right?

Thanks

Display More

Ich gebe mal die Antwort selbst

Yes the CF-card appears automatically !!
It works !!

What did I change?
I´ve tried again another CF-Card - an older one - 2GB and it works

==> So I can say the latest "SanDisk Ultra 4GB with 30MB/s" doesn´t work but the "SanDisk Extrem II 2GB" works fine

[ Hopefully it is fast enough so that the HDD isn´t slown down by the CF too much ] ...... we´ll see .....

dakeschon

Hi all,

I have the problem that I can not play recordings.
The recording is saved on the hard disk properly.

When I try to play, is a black screen.
If I copy the recording to the PC via FTP, you can also VLC can not play the recording.

Can someone give me a tip on how I can watch the recordings?

Thank you.
Temporer

there is only one chance

change the image

What?
Why? Is there an error in the image?

only my personal opinion -
the image ist not to use

Which image do you prefer for the DM600C?

i think the gemini 4.7 works stable

@ PCD
Do you think its a problem with the settings?
Or what causes my problem?