IPCamViewer for Enigma2

  • Carinthia:
    I suspect that you are running a DM800. They suffer from the 'gears' whenever anything uses any CPU. I suggest that you increase the update interval to something like 1000 or 2000ms to use less CPU. Also if the camera is not on your local LAN high update speeds will lock up the viewer as the requests will take much longer to service.
    Let us know what box this is running on and how the camera is connected - I can't see it from your posted config.

    2 x DM7025SS (Gemini2v4.4), DM600(PCD 7.0), DM800S (Gemini 4.4) TM9100(UR9B2), DM500HD, Triax 88cm dish, Technomate motor.

  • Zitat

    Original von shumifan50
    Carinthia:
    I suspect that you are running a DM800. They suffer from the 'gears' whenever anything uses any CPU. I suggest that you increase the update interval to something like 1000 or 2000ms to use less CPU. Also if the camera is not on your local LAN high update speeds will lock up the viewer as the requests will take much longer to service.
    Let us know what box this is running on and how the camera is connected - I can't see it from your posted config.


    Hey,


    it is a DM8000 and the camera is connected to the router through Power LAN. I'll try to connect the camera directly to the router to see if the Power LAN it's the problem.


    Thanks for the info.


  • Hi,


    i have exactly the same problems.
    After about 5-10 minutes there are problems and nothing works!
    I use a Dreambox 8000 and Gemini 3.
    My Image Update is set to 64 ms.


    And i use a Axis Camera.


    I hope you can Help me.

  • Dreami2 :
    As I said 2 posts ago, try increasing the update interval. Very few, if any, LANs/Cameras will cope with an update interval of 64ms. Increase this to at least 250ms if you are on a local LAN. If you are accessing over the internet increase the interval to at least 2000ms. Keep increasing the interval until you no longer get lockup and then decrease it in small steps until you find the shortest interval that is stable for your setup. This interval will vary by setup as different people run different software and plugins.


    If you reach 2 seconds on a local LAN and it is still not stable, please let me know as then there might be a different problem on the DM8000 that I will have to look at, if I can manage to borrow a DM8000.

    2 x DM7025SS (Gemini2v4.4), DM600(PCD 7.0), DM800S (Gemini 4.4) TM9100(UR9B2), DM500HD, Triax 88cm dish, Technomate motor.

    2 Mal editiert, zuletzt von shumifan50 ()

  • Thank you for your quick response.
    I use the camera only on LAN.


    I test it with 250ms and see if it works.


    :aufsmaul:


    So I have a problem.
    After 15 minutes at 250 ms there are Problems and nothing works :face_with_rolling_eyes:
    What can I do?
    If a lower value better?
    Or do I Enter a higher value?

  • Hi,


    i have a Question.
    Can I set IPCamViewer so he Starts every Time the Red Mode?
    And you can adjust the size of the images in the red mode different?


    Thank You

  • Dreami2:

    Zitat

    After 15 minutes at 250 ms there are problems and nothing works

    Keep increasing the time until it works. If it doesn't work at 2000 ms then let me know as it will need looking at.


    Zitat

    Can IPCamViewer be set to start in red mode3 every time?

    No. I will look at that in the next release. Just busy right now so I don't have time.

    Zitat

    Cam Image size be adjusted in multi-cam mode.


    No. This will require a big change.

    2 x DM7025SS (Gemini2v4.4), DM600(PCD 7.0), DM800S (Gemini 4.4) TM9100(UR9B2), DM500HD, Triax 88cm dish, Technomate motor.

  • I have tested with 2000 ms.
    After 1 Hour at 2000 ms there are Problems and nothing works :aufsmaul:
    What can I do?

  • OK. It seems there must be a memory leak or something similar then. I will look at the problem when I have a chance.
    HOWEVER:
    I need a bit more information:


    1. How many cameras are connected?
    2. Which view are you in or are you switching views?
    3. Makes of cameras.
    4. Which image and which version?
    5. PM me your config file after blanking out the username/passwords.
    6. Are you running the latest version of IPCamViewer (not the one at the start of the thread)?


    Cheers
    shumifan50

    2 x DM7025SS (Gemini2v4.4), DM600(PCD 7.0), DM800S (Gemini 4.4) TM9100(UR9B2), DM500HD, Triax 88cm dish, Technomate motor.

  • Zitat

    Original von shumifan50
    6. Are you running the latest version of IPCamViewer (not the one at the start of the thread)?


    Do you mean that the latest version is not the one at the start of the thread?

  • The latest versions will be attached to the bottom of this thread.

    2 x DM7025SS (Gemini2v4.4), DM600(PCD 7.0), DM800S (Gemini 4.4) TM9100(UR9B2), DM500HD, Triax 88cm dish, Technomate motor.

    Einmal editiert, zuletzt von shumifan50 ()

  • Hi,


    i have switch off the PIP-option in the menu...


    since then i become a green-screen! :loudly_crying_face:


    where is the config-file for this? i`ve deinstall and new install the ipcam viewer... no effect...



    Please help!!!!

  • hello ..
    From the time a plugin update?
    would be great

    2x Dm 8000, Ds409, Qnap TS-459 Pro II, SPF-107H,Onkyo TX NR-509,Teufel Consono 35,PS3,Fritzbox 7270,7390,Wii,XboX1,Down 50 Mbits, Up 10 Mbits

  • Foscam und Y-Cam


    nicht falsch verstehen, es hat alles schon mal funktioniert, bis ich diesen
    Menüpunkt umgestellt habe....


    Ich kann es aber nicht mehr rückgängig machen, da ich in das Menü so ja jetzt nicht mehr hineinkomme!


    Deshalb meine Frage nach der Config-Datei! :winking_face:

  • moin
    du musst mit einem Editor das Configfile ändern in dem Du .. mit dem DCC in



    usr/lib/enigma2/python/pluins/Extensions/IPCamViewer das Configfile editiers



    Du kannst es auch wo anders hin copieren und dann bearbeiten, aber mit z.b.


    Notepad


    gibt es alle im Downladverzeichnis

    Ich spare Strom, esse das Fleisch roh und trinke den Kaffee kalt.


    :hurra:

    Einmal editiert, zuletzt von otto19 ()

  • Danke erstmal, dass Du geantwortet hast...


    Du meinst sicher die IPCamViewer.config - die kenne ich natürlich...


    hier habe ich ja die verschiedenen Kameras eingebunden... hat ja auch funktioniert!


    Bis... ich im Menü des Plugins die Einstellung "starten PIP" auf no gestellt habe... seit dem stürzt es sofort ab.


    Diese Einstellungen sind in dieser config - Datei leider nicht enthalten... auch nicht das Speicherverzeichnis für eventl. Aufnahmen.


    Entweder es gibt noch zusätzliche Commandos oder eine andere Datei, wo diese Einstellungen abgelegt sind. Auch ein deinstallieren hat nichts geholfen... :gutenmorgen:

  • hallo totti.. das problem hatte ich auch..
    du musst es unter /etc/enigma2/settings ändern.. dort kannst du das pip wieder ändern..

    2x Dm 8000, Ds409, Qnap TS-459 Pro II, SPF-107H,Onkyo TX NR-509,Teufel Consono 35,PS3,Fritzbox 7270,7390,Wii,XboX1,Down 50 Mbits, Up 10 Mbits

  • hey... Hoffnung kommt auf! :winking_face:


    Welche von den vielen Zeilen ist es denn - rein logisch kann ich jetzt nix zuordnen


    config.skin.primary_skin=shockstyleHD/skin.xml
    config.misc.languageselected=false
    config.misc.rcused=0
    config.misc.firstrun=false
    config.misc.initialchannelselection=false
    config.misc.defaultchosen=false
    config.misc.startCounter=17
    config.misc.videowizardenabled=false
    config.Nims.1.configMode=equal
    config.Nims.0.diseqcB=192
    config.Nims.0.configMode=simple
    config.seek.selfdefined_46=60
    config.seek.selfdefined_13=15
    config.seek.selfdefined_79=300
    config.ipcam.startWithPIP=false
    config.tv.lastroot=1:7:1:0:0:0:0:0:0:0:FROM BOUQUET "bouquets.tv" ORDER BY bouquet;1:7:1:0:0:0:0:0:0:0:FROM BOUQUET "userbouquet.32ac4.tv" ORDER BY bouquet;
    config.tv.lastservice=1:0:19:EF10:421:1:C00000:0:0:0:
    config.osd.language=de_DE
    config.av.videorate.1080i=multi
    config.av.videoport=DVI
    config.av.videomode.DVI=1080i
    config.usage.blinking_display_clock_during_recording=true
    config.usage.allowed_timeshift_paths=['/media/TRANSCEND/', '/media/hdd/']
    config.usage.timeshift_path=/media/TRANSCEND/
    config.usage.multibouquet=true
    config.usage.setup_level=expert
    config.plugins.mc_globalsettings.currentskin.path=defaultHD/skin.xml
    config.plugins.autoresolution.enable=true
    config.plugins.autoresolution.videoresolution.p720_24=720p24
    config.plugins.autoresolution.videoresolution.p1080_30=1080p24
    config.plugins.autoresolution.videoresolution.p1080_24=1080p24
    config.plugins.autoresolution.videoresolution.hd_p=720p
    config.plugins.autoresolution.videoresolution.p1080_25=1080p24
    config.plugins.autoresolution.delay_switch_mode=4000
    config.plugins.FritzCall.fritzphonebook=true
    config.plugins.FritzCall.afterStandby=inList
    config.plugins.FritzCall.password=xxx
    config.plugins.FritzCall.enable=true
    config.plugins.FritzCall.lookup=true
    config.plugins.configurationbackup.backuplocation=/media/hdd
    config.plugins.configurationbackup.backupdirs=['/etc/default_gw', '/etc/enigma2/', '/etc/hostname', '/etc/network/interfaces', '/etc/resolv.conf', '/etc/wpa_supplicant.conf']
    config.plugins.crashlogautosubmit.sendmail=send_never
    config.plugins.mc_vp.showPreview=false
    config.movielist.videodirs=['/hdd/movie/']
    config.recording.margin_before=3
    config.recording.margin_after=5